654662

Icon Image 6.0 EX - IMEVEX4715.0 Manual

7
Zoom out
Zoom in
Previous page
1/14
Next page
22 7
6. Turn the Seat Post Knob (20) counterclockwise two or
three turns to loosen it. Next, pull the Knob, raise the
Seat Post (8) a few inches, and then release the Knob.
Move the Seat Post up and down slightly until the
pin on the Knob snaps into one of the holes in the
Seat Post. Then, turn the Knob clockwise until it is
tight.
Attach the Seat Bracket (7) to the Seat Post (8) with
two M8 x 25mm Patch Screws (59). Make sure that
the Seat Bracket is oriented so the slot is on the
indicated side.
7. Attach the Seat (9) to the Seat Carriage (11) with four
M8 Nylon Locknuts (38) and four M8 Split Washers
(55). Note:
The Nylon Locknuts and Split W
ashers
may be preattached to the underside of the Seat.
Slide the Seat Carriage (1
1) into the Seat Bracket (7).
Move the Seat to the desired position. Insert the Seat
Knob (10) into the slot in the side of the Seat Bracket,
and tighten the Seat Knob into the Seat Carriage.
8
59
Slot
7
20
5. Have another person hold the Console (4) near the
Handlebar (3).
Connect the Upper Wire Harness (42) to the wire har-
ness on the Console (4). Locate the two ground wires
that are connected with a screw to the Handlebar (3).
Connect the two ground wires to the two smallest wires
on the Console. Next, locate the pulse wire extending
from the Handlebar. Connect the pulse wire to the
remaining wire on the Console. Then, snap the
Handlebar Cover (5) onto the Handlebar.
Carefully insert all excess wiring into the Console (4).
Attach the Console to the metal plate on the Handlebar
(3) with four M4 x 16mm Screws (57).
Be careful to
avoid pinching the wires.
3
5
57
4
5
6
7
55
38
11
9
10
7
Do not pinch
the wires during
this step.
Pulse
Wire
Ground
Wires
42
Inspect and properly tighten all parts of the exercise
cycle regularly. To clean the exercise cycle, use a
soft, damp cloth.
To prevent damage to the console,
keep liquids away from the console and keep the con-
sole out of direct sunlight.
HOW TO ADJUST THE DRIVE BELT
If you can feel the pedals slip whilst you are pedaling,
even when the resistance is adjusted to the highest
level, the drive belt may need to be adjusted. To
adjust the drive belt, you must first remove the Right
Side Shield (27). Using an adjustable spanner, turn
the Right Pedal (21) counterclockwise and remove it.
Next, remove the indicated M4 x 25mm Screws (58).
Turn the Right Crank Arm (23) so it is pointing toward
the front of the exercise cycle, and then slide off the
Right Side Shield.
Next, turn the indi-
cated M8 Nylon
Locknut (38) until
the Drive Belt (47)
is properly tight-
ened. Then, reat-
tach the right side
shield.
PULSE SENSOR TROUBLESHOOTING
If the handgrip pulse sensor does not function properly,
see step 5 on page 12.
MAINTENANCE AND TROUBLESHOOTING
58
58
38
21
23
27
47
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icon Image 6.0 EX - IMEVEX4715.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icon Image 6.0 EX - IMEVEX4715.0 in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Icon Image 6.0 EX - IMEVEX4715.0

Icon Image 6.0 EX - IMEVEX4715.0 User Manual - German - 14 pages

Icon Image 6.0 EX - IMEVEX4715.0 User Manual - Dutch - 14 pages

Icon Image 6.0 EX - IMEVEX4715.0 User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info