670164
71
Zoom out
Zoom in
Previous page
1/104
Next page
66
8
SCAN OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Programmed scan operation (VFO mode)
Programmed scan searches for signals between
scan edge memory channels P1 and P2.
The default frequencies for these memories are
0.500000 MHz and 29.99999 MHz, respectively.
See p. 62 for scan edges programming.
q Push
V/M
to select VFO mode.
w
Push
MODE
to select the desired operating
mode.
The operating mode can be changed while scanning.
e Push
TS
to select a tuning step.
The tuning step cannot be changed while scanning.
( The programmed tuning function can be turned ON
or OFF while scanning.)
r Set the [RF/SQL] control open or closed.
• See the left page for squelch condition.
t Push
SCAN
to start the scan.
” appears while scanning.
y When the scan detects a signal, the scan turns
OFF, pauses or ignores it depending on the
resume setting and the squelch condition.
u To cancel the scan, push
SCAN
.
NOTE:
If the same frequencies are programmed
into both scan edge memory channels P1 and P2,
programmed scan does not start.
MODE
TUNER
TS
FILTER
SPCH
V/M
A/B
SPLIT
M-CL
SCAN
SET
ATT
P
.
AMP
COMP
VOX
MNF
RIT
1
2
3
4
5 6
7
8
0
50
28
1814
10
21
24
=
7
3.5
1.8
F-INP
M-CH/RIT
ENT
BAND
GENE
9
.
AGC
MW
ANF
METER
NR
NB
[RF/SQL]
Appears
Memory scan operation (Memory mode)
Memory scan searches through memory channel
1 to 199 for signals. Blank (unprogrammed) memory
channels are skipped.
q
Push
V/M
to select memory mode.
w Close the squelch with the [RF/SQL] control.
e
Push
SCAN
to start the scan.
” appears while scanning.
r When the scan detects a signal, the scan stops or
pauses depending on the resume setting.
t To cancel the scan push
SCAN
.
Rotating [DIAL] during scan also cancels scan
operation.
NOTE:
Two or more memory channels must be
programmed for memory scan to start.
MODE
TUNER
TS
FILTER
SPCH
V/M
A/B
SPLIT
M-CL
SCAN
SET
ATT
P
.
AMP
COMP
VOX
MNF
RIT
1
2
3
4
5 6
7
8
0
50
28
1814
10
21
24
=
7
3.5
1.8
F-INP
M-CH/RIT
ENT
BAND
GENE
9
.
AGC
MW
ANF
METER
NR
NB
[RF/SQL]
Appears
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7200 in the language / languages: English as an attachment in your email.

The manual is 10,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info