613740
13
Zoom out
Zoom in
Previous page
1/44
Next page
13
12. Place the rear plate (1) on the guide pins at the back of the bottom plate of the stove; then press it
in towards the stove. Lift the rear plate and press it lightly inwards until it engages with the guide
pins.
Fitting the loose parts
Before the stove is installed, you must ensure that all loose parts are fitted correctly.
Vertical cross-section of the stoves (Drawing B):
The top plate of the stove (1)
Rear smoke outlet (3). At the factory this is sealed with a cover plate. The smoke outlet is therefore
hidden behind the plate.
Top smoke outlet (4)
The smoke shelf (5). To be placed on top of the steel rail and on the holders in the sides.
Two-piece smoke defector plate (6). Each half is hung on the hooks located beneath the top plate. The
two halves join in the holders behind the air pipe. Once the stove has been installed, twist the protection
off the two hooks by using pliers or a screwdriver.
Removable rear plate (2). This must always be mounted if the stove is placed next to a combustible
wall
Loose heat shield (8) under the ash pan. This can be used as a lid when the ash pan is removed for
emptying.
Connecting and preparing the HWAM Autopilot IHS
TM
1. Connect the plug
a) to a normal 230V socket
b) to the Air box in the wood section underneath the combustion chamber (lead the plug through
the air slot at the bottom between the side and rear plates - on the left side of the wood-burning
stove when seen from the front. There is a mark on the Air box where the plug should be let in.
See the photo of the power supply on the Air box.
Air box without power supply Air box with power supply
2. Insert three AA batteries in the remote control. When the IHS logo disappears from the display,
the remote control is ready to use.
3. The remote control and the wood-burning stove must be connected (the factory will see to this).
If the status line at the bottom of the display is clear (empty) (
) and divided
into three sections, the wood-burning stove and the remote control are connected.
If the status line is dotted (
), the remote control and the wood-burning
stove are not connected. Start with a display in which the light is off, and make the connection by
pressing and holding down the button, so the advanced menu is displayed. Then press the button
repeatedly in short intervals until the text ”Link to stove” is highlighted and wait until it enters this
menu. Press the button in short intervals until the text “Connect” is highlighted and wait again.
When the text "Please cycle stove power" appears on the display, disconnect the electricity from
the Air box and then reconnect. Press the button once more. If the message "Connected to stove"
shows up in the display, the wood-burning stove and the remote control are connected. Press the
button once to return to the main menu. If you do not press the button again, the remote control
automatically leaves the menu and returns to the start display.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 3220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 3220 in the language / languages: English, Italian as an attachment in your email.

The manual is 3,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 3220

Hwam 3220 User Manual - German, Dutch, French - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info