12
11. Fix the two wires by closing the metallic tabs (4) again.
12. Installing the cover plate. Place the cover plate over the hole (above the combustion chamber,
where the flue ring was just removed) and fasten with the three screws.
13. Break off the laser-cuttings (13) on the side plates.
14. Place the sides on the guide pins (14) and hang on the screws (3) which must be fastened again.
15. Place the cast-iron top (1) on the stove.
16. Place the cast-iron top cover (15) in the hole in the cast-iron top plate.
Changing the smoke outlet from top outlet to rear outlet, HWAM 3130 (drawing E)
1. Lift the cast-iron top (1) off the stove
2. Remove the two sides of the stove by loosening the screw (2) and removing it. The two screws
(3) should only be loosened (not removed). Lift the sides off.
3. Open the metallic tabs (4) and take the wires out.
4. Pull the lambda sensor coupling (5) free of the wire fastener (6).
5. Remove the heat shield (7) and wire fastener (6) by removing the two screws (8).
6. Remove the cover plate (9).
7. Loosen the two screws (16) on each side of the heat storage compartment that support the front
plate of the heat storage compartment (17), and remove the front plate.
8. Remove the temperature monitor from the smoke ring.
9. Remove the flue ring (10) and fasten it to the rear of the stove.
10. Reattach the temperature monitor in the smoke ring, leading the sensor about 3 cm into the smoke
ring.
11. Installing the cover plate. Place the cover plate over the hole (above the combustion chamber,
where the flue ring was just removed) and fasten with the three screws.
12. Use a soft faced hammer, for instance, to break off the top of the heat shield (11) and the wire
fastener (12).
13. Fasten the heat shield (7) and wire fastener (6) to the stove again.
14. Reposition the lambda sensor coupling (5) in the wire fastener (6).
15. Fix the two wires by closing the metallic tabs (4) again.
16. Install the front (17) on the heat-storage compartment again.
17. Break off the laser-cuttings (13) on the side plates.
18. Place the sides on the guide pins (14) and hang on the screws (3) which must be fastened again.
19. Place the cast-iron top (1) on the stove.
20. Place the cast-iron top cover (15) in the hole in the cast-iron top plate.
Changing the smoke outlet from top outlet to rear outlet, HWAM 3220 (drawing F)
1. Lift the rear plate (1) and pull it away from the stove so that it disengages from the guide pins on
the bottom plate of the stove. There is a cut-out in the rear plate for the smoke outlet. Break off
the plate (2) within this cut-out to make a hole in the rear plate so there is room for the smoke
outlet.
2. Open the metallic tabs (3) and take the wires out.
3. Pull the lambda sensor coupling (4) free of the wire fastener (5).
4. Remove the heat shield (6) and wire fastener (5) by removing the two screws (7).
5. Remove the cover plate (8).
6. Remove the flue ring (9) and fasten it to the rear of the stove.
7. Use a soft faced hammer, for instance, to break off the top of the heat shield (10) and the wire
fastener (11).
8. Fasten the heat shield (6) and wire fastener (5) to the stove again.
9. Reposition the lambda sensor coupling (4) in the wire fastener (5).
10. Fix the two wires by closing the metallic tabs (3) again.
11. Place the cover plate (8) over the hole (above the combustion chamber, where the flue ring was
just removed) and fasten with the three screws.
