627050
15
Zoom out
Zoom in
Previous page
1/28
Next page
15
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
7.2. descripTion of conTrol elemenTs
Figure A – Control elements
1 Table bracket lift handle 12 Tool unload handle
2 Feed depth adjusting handle 13 Electrical cabinet handle
3 Feed depth leadscrew lock handle 14 Main motor stop button
4 Hand feed handle 15 Lamp button
5 Connect/disconnect button for electromagnetic feed
clutch
16 Coolant pump button
6 Feed regulating lever 17 Tapping select button
7 Coolant supply valve 18 Motor speed switch
8 Spindle speed change handle A 19 Power supply switch
9 Spindle speed change handle B 20 Table clamp/loose lever
10 Main motor start button 21 Bracket clamp/loose lever
11 Emergency stop button
Spindle speed change control
The 12 steps of the spindle speed are accomplished by a gear driving system and 2-speed motor (see figureE).
To change the speed, first stop the motor.
Turn the speed change handles (8 and 9) to the desired position. Then turn the switch (18) to position 1 or 2. The
speed for forward is selected. Turn the switch to position “R” for the same speed in reverse running.
Spindle feed operation
Automatic feed
First stop the motor. Turn the feed change lever (6) tot the desired feed rate on the feed chart. Push down
the button (5) on the end of the hand feed lever (4) to engage the electromagnetic clutch. Auto feed with
the selected speed starts. If you need to stop during the process, push button (5) on the control panel to
disengage the electromagnetic clutch.
Hand feed
Turn the handles (4) counter clockwise for hand feed of the spindle during drilling.
Tapping
The auto feed button should not be pushed down when tapping, because the spindle feeds according to the
pitch. For safety, please turn the tapping select button (17) to the tapping position and keep it interlocked with
auto feed.
Spindle reset
The balance and reset of the spindle are accomplished by the coiled spring. The force of spindle balance can be
adjusted by loosening the screw and turning the angle of the spring housing.
Tool loading and unloading
Tool loading
Push in the tool loading lever (12) towards the spindle box. The limit shaft blocks the spindle sleeve from rising to
its limit height. Push the tool taper shank into the spindle bore and fit tightly.
Tool unloading
Pull the tool unloading lever out. Grasp the tool with one hand, turn hand feed lever (4) with another hand. The
spindle rises rapidly. The tool shank knocks into the ram on the end of the spline shaft. The tool is pushed out.
Important remarks
1. Never pull out the tool unloading lever (12) while the machine is running. It is dangerous because when the
spindle rises and the ram on the end of the spline shaft knocks into the tool taper shaft, the tool will drop.
2. In case the tool taper shank fits in the spindle bore too tightly, turn the hand feed lever (4) quickly and make
the tool taper shank knock into the ram three times. If the tool still does not come out, extend the spindle
sleeve and use a tool unloading wedge to knock down the tool.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 30 TI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 30 TI in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 30 TI

Huvema HU 30 TI User Manual - German - 28 pages

Huvema HU 30 TI User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info