627050
14
Zoom out
Zoom in
Previous page
1/28
Next page
14
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
6. Transmission
Figure E – Transmission
6.1. lisT of gears, worm wheels, worm and rack
Number in drawing 1 2 3 4 5 6 7 8 9
Part drawing no.
Number of teeth and starts 79 1 12 36 22 48 13 1 39
Module 2.5 1.5 2.5 1.5 2.5 2 2.5 2 1.5
Direction of helical angle
4° 17’
20“
4° 17’
20“
4° 23’
55“
links
4° 23’
55“
links
Class of accuracy 9 9 9 9 8 9 9 9 9
Material 45 45 45 45 45 QT400 45 45 45
Heat treatment and hardness
T235 T235 T235 T235
T235
HV500
T235 T235 G48
Number in drawing 10 11 12 13 14 15 16 17 18
Part drawing no.
Number of teeth and starts 32 29 35 46 21 13 15 45 14
Module 1.5 1.5 1.5 1.5 1.5 1 1 1.5 1.5
Direction of helical angle
Class of accuracy 9 9 9 9 8 9 9 9 9
Material 45 45 45 45 45 45 45 45 45
Heat treatment and hardness
G48 G48 G48 G48 G48 G48
T235
G48
G48 G48
Number in drawing 19 20 21 22 23 24 25 26 27
Part drawing no.
Number of teeth and starts 68 23 50 50 50 23 45 23 54
Module 1.5 1.5 2 1 1 2 2 2 1.5
Direction of helical angle
Class of accuracy 9 9 8-7-7 9 9 8-7-7 9 9 9
Material phenolic
fiber
45 45 45 45 45 45 45 45
Heat treatment and hardness
T235 G52 G42 G42 G52 G52 G52 G52
Number in drawing 28 29 30 31 32 33 34
Part drawing no.
Number of teeth and starts
27 19 42 18 30 34 20
Module
1.5 2 2 2 2 2 2
Direction of helical angle
s of accuracy
8-7-7 8-7-7 8-7-7 9 9 8-7-7 9
Material
40Cr 45 45 45 45 45 45
Heat treatment and hardness
G52 G52 G52 G52 G52 G52 T235
7. operaTion insTrucTions
7.1. sTarTing The machine
Before starting the machine, read carefully the operation manual and become fully acquainted with all the
details.
The operator should be familiar with all the rules and points of attention for running and maintaining the
machine.
Strictly follow the instructions for lubrication. Fill the oiling places with lubricant at regular intervals.
When you push in the tool unloading spacing shaft, there should be a clearance between the end of the
taper shank of the spiral drill and the ram of the tool unloading device. Unqualified taper shanks and sleeve
adapters can not be used.
Remove all the anti-rust coating or grease from the machine. Fil the machine with lubricant. Run the machine
from low to high speed without load and check for normal functioning.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 30 TI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 30 TI in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 30 TI

Huvema HU 30 TI User Manual - German - 28 pages

Huvema HU 30 TI User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info