477553
28
Zoom out
Zoom in
Previous page
1/52
Next page
28 – English
Maintenance
Restoring from service position
1 Remove the pin and lower the cutting unit.
2 Fit the pins on both sides.
3 Lower the cutting unit to the float position
Fit the drive shaft and close the service hatch The universal
drive shaft fits only one way.
Cutting height and tilt angle
adjustment.
When a cutting unit is installed the cutting height and tilt angle
need to be adjusted
The adjustment must be made in the stated order.
Starting position:
1 Check the tyre pressures. The tyre pressure should be 1.5
bar/150 kPa/22 PSI for all wheels
The air pressure in the cutting unit pivot wheel must be
150 kPa/1.5 bar/22 psi.
2 Place the machine on a flat surface.
3 The cutting unit must be lowered onto a flat surface.
Cutting height
1 Set the same height on all three control points.
2 Hand tighten the cutting height adjustment knob.
3 Disengage the knob by pulling the handle and turning it to
the horizontal position so that the handle does not get
stuck in bushes or the like.
Height intervals are between 25-127 mm in seven different
positions.
Tilt angle
Place the machine on a flat surface.
Check the tyre pressures. The tyre pressure should be 1.5
bar/150 kPa/22 PSI for all wheels
The air pressure in the cutting unit pivot wheel must be
150 kPa/1.5 bar/22 psi.
Measure the distance between the ground and the front
and rear edges of the cutting unit hood.
The rear edge of the cutting unit should be 6-9 mm (1/4"-
3/8") higher than the front of the unit.
Loosen the lock nut and turn the adjusting screw. Extend
the brace to raise the rear edge of the cutting unit.
Lock the nut against the brace.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna P520D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P520D in the language / languages: English as an attachment in your email.

The manual is 10,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna P520D

Husqvarna P520D User Manual - English - 208 pages

Husqvarna P520D User Manual - German - 208 pages

Husqvarna P520D User Manual - German - 56 pages

Husqvarna P520D User Manual - Dutch - 208 pages

Husqvarna P520D User Manual - Dutch - 56 pages

Husqvarna P520D User Manual - French - 208 pages

Husqvarna P520D User Manual - Italian, Portuguese, Spanish - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info