595368
30
Zoom out
Zoom in
Previous page
1/48
Next page
30 – English
MAINTENANCE AND SERVICE
Cutting height and tilt angle
adjustment.
When a cutting unit is installed the cutting height and tilt angle
need to be adjusted
The adjustment must be made in the stated order.
Starting position:
1 Check the tyre pressures. The tyre pressure should be 1.5
bar/150 kPa/22 PSI for all wheels
2 Place the machine on a flat surface.
3 The cutting deck must be fully lowered on a level surface.
Cutting height - Combi 132, Combi 155
1 Position the machine on flat ground. Apply the parking
brake.
2 Raise the cutting unit halfway.
3 Turn off the motor. Adjust the cutting height by loosening
the handle and selecting the desired cutting height.
Cutting height (1-7) is indicated inside the adjusting plate.
The handle can be placed in different holes depending on
the cutting height. Set the same height on all three control
points.
4 Hand tighten the cutting height adjustment knob.
5 Adjust the control on the cutting unit. Remove the locking
pin and pull the control the required position. Set the same
height on all three control points.
Height intervals are in seven different positions.
Tilt angle - Combi 132, Combi 155
Place the machine on a flat surface.
Check the tyre pressures. The tyre pressure should be 1.5
bar/150 kPa/22 PSI for all wheels
Measure the distance between the ground and the front
and rear edges of the cutting unit hood.
The rear edge of the cutting unit should be 6-9 mm (1/4"-
3/8") higher than the front of the unit.
If necessary, loosen the lock nut and turn the adjusting
brace. Extend the brace to raise the rear edge of the
cutting unit.
Tighten the lock nut against the ball joint.
!
WARNING! Keep unauthorised persons at a
distance. You are responsible to ensure that
animals and onlookers are not within the
working area.
Frequency Approximate cutting height mm/in
1 30 / 1,18
2 40 / 1,57
3 52 / 2,04
4 64 / 2,51
5 76 / 2,3
6 93 / 3,66
7 112 / 4,4
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna P 520D - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P 520D - 2015 in the language / languages: English as an attachment in your email.

The manual is 12,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna P 520D - 2015

Husqvarna P 520D - 2015 User Manual - German - 48 pages

Husqvarna P 520D - 2015 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info