595368
28
Zoom out
Zoom in
Previous page
1/48
Next page
28 – English
MAINTENANCE AND SERVICE
Adjusting the parking brake
Make sure the parking brake is properly adjusted by placing
the machine on a slope.
Apply and lock the parking brake.
When the machine does not stand still, the parking brake
should be adjusted according to the following.
1 Position the machine on flat ground.
2 Make sure the parking brake is released.
3 Adjust so there is 1 mm play between the outer cable and
the adjuster screw when you pull the outer cable.
Adjust the adjuster screw using the nuts.
4 Tighten the nuts carefully to prevent damaging the
adjuster screw.
5 The parking brake should be checked again after the
adjustment has been made.
Replacing the light bulbs
For information about the bulb type, see Technical Data.
1 Unscrew the four screws holding the cover on the power
servo housing.
2 Unscrew the two screws holding the lamp insert.
3 Lift out the lamp insert.
4 Disconnect the cables from the bulbs.
5 Lift out the bulbs from the insert.
6 Insert the new bulbs. Make sure you use your thumb to
support the front.
7 Refit the cables, lamp insert and the cover on the power
servo housing.
Main fuse
The machine has a high-power safety fuse located in a box on
the top of the battery plus terminal.
A feeder fuse for the electrical connection box is located on
a bracket near the battery.
Other fuses are in the electrical connection box behind right
side cover.
A blown fuse is indicated by a burnt connector. Pull the fuse
from the holder when replacing.
The fuse is there to protect the electrical system.
Do not use any other type of fuse when replacing. If it blows
again shortly after replacement, it is due to a short circuit,
which must be fixed before the machine can be put into
operation again.
Service position for the cutting unit
The cutting head can be placed in the service position to
provide easy access for cleaning, repairs and servicing. In the
service position the cutting unit is raised and locked in the
vertical position.
Placing in the service position
1 Position the machine on flat ground. Apply the parking
brake.
2 Raise the cutting unit halfway.
3 Turn off the motor.
4 Remove the lifting eyes from the cutting unit.
!
WARNING! A poorly adjusted parking brake
can result in reduced braking ability.
!
WARNING! Never leave the universal drive
shaft of the machine with one end loose. If
the engine is started, damage can occur.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna P 520D - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P 520D - 2015 in the language / languages: English as an attachment in your email.

The manual is 12,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna P 520D - 2015

Husqvarna P 520D - 2015 User Manual - German - 48 pages

Husqvarna P 520D - 2015 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info