436321

HP designjet 8000s cutter blade kit Manual

19
Zoom out
Zoom in
Previous page
1/230
Next page
Handling precautions
These precautions are recommended to avoid damage to your printer and its components.
Power supply
●
Use the power supply voltage specified on the nameplate.
●
Check the printer electrical outlet for proper polarity and grounding before connecting printer. Failure
to do so may result in fire and electric shock hazards.
●
Be sure the printer is well-grounded. Failure to ground the printer may result in electrical shock, fire,
and susceptibility to electromagnetic interference.
●
Avoid overloading the printer’s electrical outlet with multiple devices.
●
Use only the electrical cable supplied by HP with the printer.
Printer
●
Wipe the printer clean with a soft cloth. A cloth moistened with a neutral detergent may be used. Do
not allow liquid to enter the printer. This may create risk of fire and electrical shock and cause a
malfunction. Do not clean the printer with benzene or paint thinner. This may damage the paint.
●
Never touch the printhead nozzles. They can be easily damaged or clogged.
Regular inspection and maintenance
●
Make sure you observe the appropriate maintenance guideline. See
How do I maintain the printer.
●
Clean the capping unit every day.
●
Never switch off the printer without following the correct procedures. Even with the storage liquid
installed, never leave the printer off for more than 4 weeks. Leaving your printer off for more than 4
weeks can cause permanent damage that cannot be repaired. In all other cases make sure you
observe the appropriate maintenance guidelines.
Consumables
●
Ink inside the ink cartridge is combustible. Do not expose or store near open flames, sparks, or other
sources of ignition.
●
HP Ink Cartridges should be installed before the “Install By” date printed on the cartridge. Use of the
Ink Cartridge 3 months beyond the “Install By” date may cause deterioration in print quality or a printer
malfunction.
●
Do not disassemble the ink cartridges. Ink cartridges are intended for single use only.
●
Avoid contact between ink and skin, eyes, and clothing.
●
Immediately wash skin with soapy water.
●
Remove clothing soaked with ink from contact with skin.
●
Use an approved eye wash station if ink is splashed into eyes and consult a doctor if necessary.
If an approved eye wash station is unavailable, flush eyes with cold water and consult a doctor
if necessary.
ENWW Handling precautions 9
Introduction
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HP designjet 8000s cutter blade kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HP designjet 8000s cutter blade kit in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info