646888
27
Zoom out
Zoom in
Previous page
1/132
Next page
4.3 Connecting additional
components / accessories
ATTENTION
External voltage on the connecting terminals
External voltage on the connecting terminals of the control
will destroy the electronics.
Do not apply any mains voltage (230 / 240VAC) to the
connecting terminals on the control.
The terminals that the additional components are connected
to, such as volt-free internal push buttons, key switches or
photocells, only carry a non-hazardous low-voltage current of
approx. 24VDC.
To prevent malfunctions:
Duct the operator‘s connection cables (24VDC) in an
installation system that is separate from other supply
lines (230 / 240VAC).
4.3.1 Electrical connection/connecting terminals
See figure10
Remove the side flap on the operator cover in order to
access the connecting terminals for additional
components.
NOTE:
All connecting terminals can be given multiple assignments,
but with a maximum of 1×1.5mm
2
(seefigure11).
Loading of the operator by all accessories: max. 250mA.
4.3.2 External buttons*
See example an for internal push button in figure12
One or more buttons with normally open contacts (volt-free)
can be connected in parallel.
4.3.3 2-wire photocell*
NOTE:
Follow the fitting instructions when mounting photocells.
Connect the photocells as shown in figure13.
After the photocell triggers, the operator stops and, after a
short pause, a safety reversal of the door is performed to the
OPEN end-of-travel position.
4.4 DIL switch functions
See figure10
Several of the operator‘s functions must be programmed
using the DIL switches. Before initial start-up, the DIL
switches are in the factory settings, i.e. all the switches are in
the OFF position.
NOTE:
Only change the DIL switch settings when the operator is at
arest and no radio codes are being programmed.
Set the DIL switches as described below in accordance with
the national regulations, the desired safety equipment and the
on-site conditions.
* Accessory, not included as standard equipment!
4.4.1 DIL switch A: activate 2-wire photocell
See figure13
If the light path is interrupted during closure, the operator will
stop immediately and, after a short pause, travel until it
reaches the OPEN end-of-travel position.
ON 2-wire photocell
OFF
No safety device (delivery condition)
4.4.2 DIL switch B: without function
5 Radio
WARNING
Danger of injury during unwanted
door travel
Pressing a button on the hand
transmitter may result in unwanted door
cycles and cause injury.
Make sure that the hand
transmitters are kept away from
children and can only be used by
people who have been instructed
on how the remote-control door
functions!
If the door has only one safety
feature, only operate the hand
transmitter if you are within sight of
the door!
Only drive or pass through remote
control door systems when the door
is at a standstill!
Never stay standing under the open
door.
Please note that unwanted door
cycles may occur if a hand
transmitter button is accidentally
pressed (e.g. if stored in a
pocket / handbag).
CAUTION
Danger of injuries due to unintended door travel
Unwanted door travel may occur while teaching in the radio
system.
Pay attention that no persons or objects are in the
door's travel range when teaching in the radio system.
ATTENTION
Functional disturbances caused by environmental
conditions
These conditions can impair function!
Protect the hand transmitter from the following conditions:
• Direct sunlight
(perm.ambienttemperature:– 20°Cto+ 60 °C)
• Moisture
• Dust
• If there is no separate garage entrance, perform all
teach-in processes, program changes and extensions
while standing in the garage.
TR10L006-C RE / 11.2013 27
ENGLISH
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann Liftronic 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Liftronic 700 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 12,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info