646888
28
Zoom out
Zoom in
Previous page
1/132
Next page
• After teaching-in or extending the radio system, perform
a function check.
• Only use original components when extending the radio
system.
5.1 Hand transmitter RSC2
The hand transmitter works with a rolling code that changes
with each sending procedure. For this reason, it must be
taught in with the desired hand transmitter button on each
receiver that is to be controlled (seesection5.3 or the
receiver‘s operating instructions).
5.1.1 Control elements
See figure14
1 LED
2 Hand transmitter button
3 Battery
5.1.2 Inserting / changing the battery
See figure14
Only use the battery type C2025, 3VLi, and pay
attention to the correct polarity.
5.1.3 Hand transmitter LED signals
• LED illuminated:
The hand transmitter is sending a radio code.
• LED flashing:
The hand transmitter is transmitting, but the battery
charge is so low that it must be replaced soon.
• No LED response:
The hand transmitter is not functioning.
Check whether the battery has been inserted
correctly.
Exchange the battery for a new one.
5.1.4 Excerpt from the manufacturer‘s declaration
Conformity of the above-mentioned product with the
requirements of the directives according to article 3 of the
R&TTE directives 1999/5/EC was verified by compliance with
the following standards:
• EN 300 220-2
• EN 301 489-3
• EN 50371
• EN 60950-1
The original declaration of conformity can be requested from
the manufacturer.
5.2 Integral radio receiver
The garage door operator is equipped with an integral radio
receiver. A maximum of 6 different hand transmitter buttons
can be taught in. If more are taught in, the first one will be
deleted without advance warning. All memory spaces are
empty in the delivery condition. They can only be taught in or
deleted when the operator is at a standstill.
5.3 Teaching in hand transmitters
See figure15
1. Briefly press the Pbutton on the operator cover.
The red LED will begin to flash, signalling readiness for
the teach-in process.
2. Hold the desired hand transmitter button down until the
LED begins flashing rapidly.
3. Release the hand transmitter button and press it again
within 15seconds until the LED begins flashing very
rapidly.
4. Release the hand transmitter button.
The red LED remains lit and the hand transmitter button
is taught in and ready for operation.
5.4 Operation
At least one hand transmitter button must be taught in on the
radio receiver to operate the garage door operator via radio.
During radio transmission, the hand transmitter and receiver
must be at least 1 m apart.
5.5 Deleting all memory spaces
See figure16
It is not possible to delete individual memory spaces. The
following step will delete all the memory spaces in the integral
radio receiver (delivery condition).
1. Press and holdthe Pbutton on the operator cover.
The red LED first flashes slowly and then becomes more
rapid.
2. Release the Pbutton.
All memory spaces have now been deleted. The red LED will
remain lit.
NOTE:
The deletion process will be aborted if buttonP is released
within 4seconds.
6 Operation
WARNING
Danger of injury during door travel
If people or objects are in the area
around the door while the door is in
motion, this can lead to injuries or
damage.
Make sure that children are not
playing near the door system.
Make sure that no persons or
objects are in the door's travel
range.
If the door system has only one
safety feature, only operate the
garage door operator if you are
within sight of the door's area of
travel.
Monitor the door travel until the
door has reached the end-of-travel
position.
Only drive or pass through remote
control door systems when the
door is at a standstill!
Never stay standing under the open
door.
CAUTION
Danger of crushing in the boom
Do not reach into the boom with your fingers during door
travel, as this can cause crushing.
Do not reach into the boom during door travel.
28
TR10L006-C RE / 11.2013
ENGLISH
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann Liftronic 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Liftronic 700 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 12,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info