646888

Hormann Liftronic 700 Manual

25
Zoom out
Zoom in
Previous page
1/132
Next page
3.4.2 Up-and-over doors with an ornamental iron
handle
▶
See figure1.6b
▶
In a deviation from the illustrated section, attach the lintel
ceiling console and link bracket max. 50 cm off-centre for
up-and-over doors with ornamental iron door handles.
3.4.3 Up-and-over doors with timber infill
▶
See figure1.7b
For N80 doors with timber infill, the bottom holes on the lintel
joint must be used for fitting.
3.5 Assembling the operator boom
CAUTION
Crushing hazard during boom fitting!
There is a danger of crushing your fingers while fitting the
operator boom.
▶
Make sure that your fingers do not get between the
profile ends.
▶
Use the enclosed fitting instructions to install the boom.
▶
Before assembling the last boom segment, place the
boom in front of a stable surface (e.g. a wall) that can
serve as a counter support.
▶
Check to see if the toothed belt is located on the centre
of the return pulley. If it is not, shift the toothed belt to the
centre using a blunt object (e.g. with the blunt end of a
wrench).
▶
Check the toothed belt tension and adjust if necessary
(seefigure17 and section7.1).
3.5.1 Checking that the slide carriage is easy to move
▶
See figure2.1
1. Make sure that the individual boom segments are aligned
with one another so that there are smooth transitions at
each profile end!
2. Check to make sure that the slide carriage can be easily
moved in the boom. To do this, push the slide carriage
back and forth in the boom once. Repeat this procedure,
if necessary.
3.5.2 Fitting the operator boom
▶
See figures2.2 – 2.5
WARNING
Unsuitable fixing material
Use of unsuitable fixing material may mean that the
operator is insecurely attached and could come loose.
▶
The fitter must check that the fitting materials supplied
are suitable for the purpose and the intended fitting
location.
▶
Only use the provided fixing materials (plugs) in
concrete ≥B15 (seefigures1.6a / 1.8b / 2.5).
ATTENTION
Damage caused by dirt
Drilling dust and chippings can lead to malfunctions.
▶
Cover the operator during drilling work.
▶
Before the boom is fitted on the lintel and under the
ceiling, shift the slide carriage approx. 20cm towards the
middle of the boom. At a later point, this will no longer be
possible!
3.6 Determining the door end-of-travel positions
▶
See figure3.1a / 3.1b – 5.2
1. Assemble the fitting bracket.
2. Loosely insert the end stop for the OPEN end-of-travel
position in the boom between the slide carriage and
operator and manually push the door into the OPEN end-
of-travel position.
This will push the end stop into the correct position.
3. Tighten the end stop for the OPEN end-of-travel position.
4. Loosely insert the end stop for the CLOSE end-of-travel
position in the boom between the slide carriage and the
lintel ceiling console and manually push the door into the
CLOSE end-of-travel position.
This will push the end stop into the correct position.
5. Tighten the end stop for the CLOSE end-of-travel
position.
NOTE:
If the door cannot be easily pushed manually into the desired
OPEN or CLOSE end-of-travel position, this means that the
door mechanism is too stiff for operation with the garage door
operator and must be inspected (seesection3.1)!
3.7 Fitting the garage door operator
▶
See figure 6
WARNING
Danger of injury due to unwanted door travel
Incorrect assembly or handling of the operator may trigger
unwanted door travel that may result in persons or objects
being trapped.
▶
Follow all the instructions provided in this manual.
Incorrectly attached control devices (e.g. buttons) may
trigger unwanted door travel. Persons or objects may be
trapped as a result.
▶
Install control devices at a height
of at least 1.5m (out of the reach
of children).
▶
Fit permanently installed control
devices (such as buttons, etc.)
within sight of the door, but away
from moving parts.
3.8 Emergency release
An emergency release lock for a mechanical release is
required for garages without a second entrance in order to
prevent users from locking themselves out in the case of a
power failure (to be ordered separately, see Accessories for
garage door operator C8).
▶
Check the emergency release monthly for proper
function.
3.9 Fixing the warning sign
▶
See figure7
▶
Fix the sign warning about getting trapped in a
noticeable, cleaned and degreased place, for example,
near to the permanently installed button for moving the
operator.
TR10L006-C RE / 11.2013 25
ENGLISH
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann Liftronic 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Liftronic 700 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 12,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info