Manual Hitachi DS 12 DVF 3 (page 14 of 108) (English, German, Dutch, French, Italian, Portuguese, Spanish)

78142

Zoom out

Zoom in

1/108

English

Table 4

Rechargeable batteries

Temperatures at which

the battery can be

recharged

EB912S, EB914S, BCC915,

EB9B, EB1212S, EB1214S,

BCC1215, EB1220BL,

EB1412S, EB1414S,

BCC1415, EB14B,

EB1814SL, BCC1815,

EB1820L

0°C — 45°C

BCH1220, BCH1420,

BCH1820

–5°C — 50°C

(3) Regarding recharging time

Table 5 shows the recharging time required according to

the type of battery.

Table 5 Recharging time

(approx. min.) at 20°C

Charger

Battery

UC18YGH

EB912S, EB914S, BCC915,

EB1212S, EB1214S,

BCC1215, EB1412S,

EB1414S, BCC1415,

EB1814SL, BCC1815

Approx. 30 min.

EB9B, EB1220BL, EB14B,

EB1820L, BCH1220,

BCH1420, BCH1820

Approx. 50 min.

NOTE

The recharging time may vary according to the ambient

temperature.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out

the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and

normal time required for recharging

will be restored by recharging the batteries 2-3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be

damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use.

If such a battery is recharged immediately after use, its

internal chemical substance will deteriorate, and the

battery life will be shortened. Leave the battery and

recharge it after

it has cooled for a while.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by following the

precautions.

HOW TO USE

1. Conﬁ rm the clutch dial position (See Fig. 5)

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the clutch

dial is set.

(1) When using this unit as a screwdriver, line up the one of

the numbers “1, 3, 5 ...

22” on the clutch dial, or the dots,

with the triangle mark on the outer body.

(2) When using this unit as a drill, align the clutch dial drill

mark “

” with the triangle mark on the outer body.

CAUTION

○ The clutch dial cannot be set between the numerals “1, 3,

5 ... 22” or the dots.

○ Do not use with the clutch dial numeral between “22”

and the line at the middle of the drill mark. Doing so may

cause

damage (See Fig. 6).

2. Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity to

the screw diameter. When too strong torque is used,

the screw head may be broken or be injured. Be sure

to adjust the clutch dial position according to the screw

diameter.

(2)

Tightening torque indication

The tightening torque diﬀ ers depending on the type of

screw and the material being tightened.

The unit indicates the tightening torque with the numbers

“1, 3, 5 ... 22” on the clutch dial, and a dots. The tightening

toque at position “1” is the weakest and

the torque is

strongest at the highest number (See Fig. 5).

(3) Adjusting the tightening torque

Rotate the clutch dial and line up the numbers “1, 3, 5 ...

22” on the clutch dial, or the dots, with the triangle mark

on the outer body. Adjust the clutch dial in

the weak or

the strong torque direction according to the torque you

need.

CAUTION

○ The motor rotation may be locked to cease while the unit

is used as drill. While operating the driver drill, take care

not to lock the motor.

○ Too long hammering may cause the screw broken due

excessive tightening.

3. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (See

Figs. 7 and 8).

When the shift knob is set to “LOW”, the drill rotates at a

low speed. When set to “HIGH”, the

drill rotates at a high

speed.

CAUTION

○ When changing the rotational speed with the shift knob,

conﬁ rm that the switch is oﬀ .

Changing the speed while the motor is rotating will

damage the gears.

○ When setting the shift knob to “HIGH” (high speed)

and the position of the

clutch dial is “17” or “22”, it may

happen that the clutch does not engaged and that the

motor is locked. In such a case, please set the shift knob

to “LOW” (low speed).

○ If the motor is locked, immediately turn the power oﬀ . If

the motor is

locked for a while, the motor or battery may

be burnt.

000Book_DS9DVF3_WETha.indb 14000Book_DS9DVF3_WETha.indb 14 2012/06/06 8:46:142012/06/06 8:46:14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS 12 DVF 3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi DS 12 DVF 3

Hitachi DS 12 DVF 3 User Manual - English, Danish, Swedish, Norwegian, Finnish - 46 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi DS 12 DVF 3 Manual

Product: