78142
12
Zoom out
Zoom in
Previous page
1/108
Next page
English
12
4. Battery (EB1814SL, BCC1815, EB1820L, BCH1820)
(For DS18DVF3)
Optional accessories are subject to change without notice.
APPLICATIONS
Driving and removing of machine screws, wood screws,
tapping screws, etc.
Drilling of various metals.
Drilling of various woods.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch (1 pc.
or 2 pcs.) to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
<UC9SD/UC12SD>
Before using the driver drill, charge the battery as follows.
1. Insert the battery into the charger
Insert the batteryrmly while observing its direction, until
it contacts the bottom of the charger (See Fig. 3).
CAUTION
The UC9SD and UC12SD models are the exclusively
designed charger. These cannot charge batteries
except the speci ed batteries. It is possible to insert
the batteries other than the speci ed into the charger
and some of them may light up the pilot lamps.
However, you are requested to exercise utmost
caution not to charge batteries other than speci ed
ones because these can not
only be charged but
also such actions can result in the malfunction of
chargers.
2. Connect the charger power cord to the receptacle.
Connecting the power cord will turn on the charger (the
pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the power
cord from
the receptacle and check the battery
mounting condition.
About 60 minutes are required to fully charge the battery
at a temperature of about 20°C. The pilot lamp goes o to
indicate that the battery is fully charged.
The battery charging time becomes longer when a
temperature is low or the
voltage of the power source is
too low.
When the pilot lamp does not go o even if more than 120
minutes have elapsed after starting of the charging, stop
the charging and contact your HITACHI AUTHORIZED
SERVICE CENTER.
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may not
light up. At that time, cool the batteryrst, then start
charging.
3. Disconnect the charger power cord from the
receptacle
4. Hold the charger rmly and pull out the battery
NOTE
After charging, pull out batteries from the chargerrst,
and then
keep the batteries properly.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them therst and second time. This is a temporary
phenomenon, and
normal time required for recharging
will be restored by recharging the batteries 2 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be
damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after use.
If such a battery is recharged immediately after use, its
internal chemical substance will deteriorate, and the
battery life will be shortened. Leave the battery and
recharge it after
it has cooled for a while.
<UC18YG/UC18YK>
Before using the driver drill, charge the battery as follows.
1. Connect the charger power cord to the receptacle
Connecting the power cord will turn on the charger.
2. Insert the battery into the charger
Insert the batteryrmly while observing its direction,
until it contacts
the bottom of the charger (See
Fig. 4) (the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the power
cord from the receptacle and check the battery
mounting condition.
(1) Regarding the temperatures of the rechargeable battery
The temperatures for rechargeable batteries are as
shown
in Table 1.
Table 1 Recharging ranges of batteries
Rechargeable batteries
Temperatures at
which the battery
can be recharged
EB912S, EB914S, BCC915,
EB9B, EB1212S, EB1214S,
BCC1215, EB1220BL,
EB1412S, EB1414S,
BCC1415, EB14B,
EB1814SL, BCC1815,
EB1820L
0°C 45°C
(2) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 2.
000Book_DS9DVF3_WETha.indb 12000Book_DS9DVF3_WETha.indb 12 2012/06/06 8:46:142012/06/06 8:46:14
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi DS 12 DVF 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS 12 DVF 3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi DS 12 DVF 3

Hitachi DS 12 DVF 3 User Manual - English, Danish, Swedish, Norwegian, Finnish - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info