565926

Hitachi CM14E Manual

15
Zoom out
Zoom in
Previous page
1/232
Next page
15
GB
Set cutter down on level ground with wheel or cutter blade in the clear.
Grasp front handle with left hand, and hold down rear handle with toe of your
boot. Never “drop-start” the cutter.
WARNING
Wheel will rotate when engine is started at latched throttle setting.
Keep cutting wheel in the clear.
IMPORTANT
z Check unit for loose nuts, bolts and screws before starting.
z Always clear work area of debris before starting operation.
z Always hold the unit fi rmly.
z When pulling starting rope, use short pulls, 1/2 to 2/3 of rope length.
z Do not allow the starter grip to snap back against the housing.
Operation
2-Stroke Fuel
z Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine
oil of reputable brand name. Minimum 89 Octane unleaded petrol is
recommended. Do not use fuel containing methyl alcohol or more than 10
% of ethyl alcohol.
z Recommended mixture ratio; 50 : 1 (2 %) for ISO-L-EGD Standard (ISO/
CD 13738), JASO FC, FD grade.
- Do not mix directly in engine fuel tank.
- Avoid spilling petrol or oil. Spilled fuel should always be wiped up.
- Handle petrol with care, it is highly infl ammable.
- Always store fuel in approved container.
1. Pour 1/2 of the petrol into a safe container.
2. Add oil to the petrol and mix them.
3. Add remaining petrol and mix again.
4. Install fuel cap and wipe spilled fuel from cutter, container and the area.
IMPORTANT
Do not mix fuel in engine fuel tank.
Starting and Stopping
Safe Starting Techniques
Starting Cold Engine
1. Pull out choke all the way.
2. Move ignition switch to “RUN” position.
3. Depress and hold throttle trigger and lockout
while pushing in latch button to latch throttle for
starting.
4. Crank engine. Pull starter grip briskly, but only
1/2 to 2/3 its full length. Pulling rope to the end
may damage the starter.
5. Push in the choke the fi rst time engine fi res,
and crank until engine starts and runs. In cold
weather you should keep the choke out just a
little until the engine gets very warm. But, do not
operate with the choke out.
6. Squeeze and release trigger when engine runs.
You now have trigger control of the throttle
speed.
3
Depress and Hold Both
Throttle Trigger and
Lockout Lever, and
Push in Latch Button,
then Release Trigger
1
Pull out Choke
2
Move Switch to “RUN”
6
To De-latch Throttle, Squeeze
and Release the Trigger
4
Pull Starter Grip
CM14E_WE_all.indb 15CM14E_WE_all.indb 15 2008/02/05 21:09:322008/02/05 21:09:32
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM14E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM14E in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info