565926

Hitachi CM14E Manual

16
Zoom out
Zoom in
Previous page
1/232
Next page
16
GB
1. Squeeze and release trigger to unlatch it and take control of the throttle.
2. Let engine warm to operating temperature before doing any cutting.
3. Take cutting stance on left side of cutter. Never get any part of your body
behind the cutter. Hold the cutter fi rmly with both hands. Throttle up to
cutting speed and make gentle wheel contact with the work.
Stopping Engine
Move ignition switch down to “STOP” position. Keep wheel in the clear until
all movement stops.
If engine does not stop, pull choke control knob out fully to stop engine. The
choked engine will slow to a stop. Be sure to keep the wheel in the clear until
all movement stops.
WARNING
With trigger latched, wheel will rotate as soon as engine starts. Keep
wheel in the clear.
Wheel will rotate for some time after the trigger is released. Keep
wheel in the clear until all movement stops.
Restarting Warm Engine
When engine is warm from previous running, move ignition switch to
“RUN” position. And push choke control knob all the way in. Try cranking
at idle throttle without latching it. If this does not work, try again with throttle
latched. Choking may be needed if the engine has cooled. But, to avoid
the possibility of over-choking and fl ooding, always fi rst try to start a warm
engine without choking it.
Sequence after Starting Engine
Cutting Asphalt, Tar and Reinforced Materials
Old, cold and hardened asphalt paving can be cut with a masonry wheel with
good results and little trouble with tarring of the wheel. Fresh asphalt and
tarred surfaces can gum up the wheel and slow its cutting action. Some tar
or resin-impregnated materials also may present problems of this sort.
Masonry containing metal reinforcement is best cut with a masonry wheel
which can cut through the reinforcing steel better than a wheel designed for
metal can cut the masonry. Expect faster than normal wheel wear.
DANGER
z Do not raise cutter above chest height, because the cutter is hard
to control when held up high, and dust or sparks will fall on you.
z Wear hearing protection. Without it you risk hearing loss,
especially where bounce-back of sound waves off nearby surfaces
increases the noise.
z Do not take awkward or risky operating positions. Find solid
footing for both feet, and always hold the cutter fi rmly with both
hands. Never make one-handed cuts.
z When the wheel engages the work, the thrust will exert a forward
pull which you must be ready to control. Keep bystanders out of
the way.
Wheel Thrust
CM14E_WE_all.indb 16CM14E_WE_all.indb 16 2008/02/05 21:09:322008/02/05 21:09:32
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM14E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM14E in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info