801892
24
Zoom out
Zoom in
Previous page
1/100
Next page
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 7 of 16 AquaRite® Pro LS Rev. D
SETTINGS: Push the SETTINGS button to enter the Settings Menu.
CURSORS (+, -, <, >): Use these buttons to scroll through submenus, make selections and adjust values.
Indicator LED's
RUN/STOP: When illuminated, the AquaRite Pro LS is in automatic mode and will produce chlorine based on the
desired output % or ORP setting (when AQL-CHEM is used). When the LED is off, the AquaRite Pro LS has been
manually turned off. It will not produce chlorine until RUN has been selected.
SUPER CHLORINATE: When illuminated, the Super Chlorinate feature is active.
CHECK SYSTEM: When Check System is illuminated, an error has occurred that requires attention. Refer to the
Troubleshooting section of this manual for possible errors and solutions.
Information Menu
The Information Menu displays valuable system and pool information. The AquaRite Pro LS will default to displaying
a portion of the Information Menu when no buttons have been pushed for 2 minutes. The unit will automatically scroll
through several status displays. To access all of the Information Menu items, push the INFO button on the front panel.
Advance through the various menu items using the "<" or ">" buttons. A list of the Information Menu items is shown below.
If ORP Auto Sensing is not used
Chlorinator
50 %
No Function
Move to previous/next menu item
Super Chlorinate
22:15 remaining
No Function
Move to previous/next menu item
The AquaRite Pro LS desired output % is shown here. If Super Chlorinate is active, the display will show
the time remaining until the AquaRite Pro LS will return to the desired output %. This menu is disabled if
an AQL-CHEM is used and ORP Auto Sensing is enabled (see AQL-CHEM manual).
If AQL-CHEM is used
No Function
Move to previous/next menu item
pH 7.5 (On)
ORP 700 mV (On)
This display will be shown only if chemical sensing is enabled. This display shows both pH and ORP
levels/status when chemistry sensing is enabled via the Chemistry Configuration Wizard (requires the
use of AQL-CHEM Sensing Kit). The AquaRite Pro LS will refer to these levels to determine how much
chlorine to generate (ORP) and how much acid to dispense (pH). Refer to the AQL-CHEM manual for
specific information about these levels as well as the recommended ranges.
Press to switch chlorinator operation to opposite polarity (15 second delay)
Move to previous/next menu item
+23.45 +6.75A
29°C 1.5 g/L
+/- 23.45V is the voltage applied to the chlorinator cell
+/-6.75A is the current (amps) through the cell
29°C is the water temperature at the cell
1.5 g/L is the “instant” salt level at this time
For the chlorinator to be operating, several conditions must exist: the filter pump must be running,
the flow switch must be detecting flow, the chlorinator setting must be set greater than 0%, the water
temperature at the cell must be between 12ºC and 60ºC, and the salt level must be within the operating
range. If any of these conditions are not met, the chlorinator diagnostic display will tell you the reason.
It’s possible to have more than one reason, in which case after you rectify what was displayed the first
time, a second display will appear.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hayward Aqua Rite Pro LS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hayward Aqua Rite Pro LS in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info