801892

Hayward Aqua Rite Pro LS Manual

22
Zoom out
Zoom in
Previous page
1/100
Next page
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 5 of 16 AquaRite® Pro LS Rev. D
Si = pH + Ti + Ci + Ai - 12.1
°C °F Ti Calcium
Hardness Ci Total
Alkalinity Ai
12
16
19
24
29
34
39
53
60
66
76
84
94
100
0.3
0.4
0.5
0.6
0.7
0.8
0.9
75
100
125
150
200
250
300
400
600
800
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.4
2.5
75
100
125
150
200
250
300
400
600
800
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.8
2.9
How to use: Measure pool pH, temperature, calcium hardness, and
total alkalinity. Use the chart above to determine Ti, Ci and Ai into the
above equation. If Si equals 0.2 or more, scaling and staining may
occur. If Si equals -0.2 or less corrosion or irritation may occur.
{
- 0.2 0.20
OK
CORROSIVE SCALING
Salt Level
Use the chart on page 6 to determine how much salt in kgs need to be added to reach the recommended levels. Use the
equations below if pool size is unknown.
M³
(pool size in meters)
Rectangular Length x Width x
Average Depth
Round Diameter x Diameter x
Average Depth x 0.785
Oval Length x Width x
Average Depth x 0.893
The ideal salt level is between 1.2 - 2.5 g/L with 1.5 g/L being optimal. If the level is low, determine the number of M³ in
the pool and add salt according to the chart on page 6. A low salt level will reduce the efficiency of the AquaRite Pro LS
and result in low chlorine production. A high salt level can cause the AquaRite Pro LS to shutdown and may begin to give
a salty taste to your pool. The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming
season should be small. This loss is due primarily to the addition of water because of splashing, backwashing, or draining
(because of rain). Salt is not lost due to evaporation.
Type of Salt to Use
It is important to use only sodium chloride (NaCl) salt that is greater than 99% pure (EN 16401). Use only salt for
electronic chlorine generator usually available in 25 kg bags. Do not use rock salt, salt with yellow prussiate of soda, salt
with anti-caking additives, or iodized salt.
How to Add or Remove Salt
For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure. Turn the circulating pump on and
add salt directly into the pool. Brush the salt around to speed up the dissolving process. Do not allow salt to pile up on the
bottom of the pool. Run the filter pump for 24 hours with the suction coming from the main drain (use pool vac if there is
no main drain) to allow the salt to evenly disperse throughout the pool. The salt display may take 24 hours to respond to
the change in salt concentration.
The only way to lower the salt concentration is to partially drain the pool and refill with fresh water.
Always check stabilizer (cyanuric acid), when checking salt. These levels will most likely decline together. Use the
chart on page 6 to determine how much stabilizer must be added to raise the level to 25 ppm. Use stabilizer only if
necessary.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hayward Aqua Rite Pro LS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hayward Aqua Rite Pro LS in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info