Manual Hanseatic XL 25 T (page 32 of 40) (English, German, French, Italian)

519139

Zoom out

Zoom in

1/40

GB-4

2. Use the included screw (E) and nut (F) to fix the

protection cover (Fig. 3).

ATTENTION : Make sure that all components are

mounted and assembled correctly and all screws

properly tightened.

ATTENTION ! - Do always act in accordance with

the applicable safety instructions and apply all

required safety measures. The trimmer may

only be used to cut grass or smaller weeds. It

is explicitly forbidden to cut any other kind of

material. Do not use the trimmer as a lever to

lift, remove or crush objects; do also not x it to

rigid holding devices. It is forbidden to mount any

devices or supplements to the trimmer’s drive unit

that are not explicitly released for that purpose by

the manufacturer.

MOUNTING THE ATTACHMENT (Fig. 4–6)

Attention: Switch off the device before mounting

the attachment. DANGER OF INJURY !

Note: To facilitate mounting and dismounting the attach-

ment put the tool on the ground or a workbench.

1. Loosen the knob (A) by turning it anticlockwise (Fig.

4).

2. Hold the attachment (B) and push it straightly into the

quick-change coupling (C) until the release button (D)

engages into the corresponding hole (E) of the coupling

(Fig. 4+5).

3. Turn the knob (A) clockwise to tighten it (Fig. 6).

Attention: Before operation, the release button

must have engaged into the hole of the coupling

and the knob must have been tightened rmly!

FUEL AND OIL

FUEL

For a maximum performance of your trimmer, use

regular petrol (two-star, unleaded) mixed with a special

2-stroke engine oil (40:1). Please adhere to the mixing

instructions.

ATTENTION : Do never use pure fuel without oil. This

will damage the engine and you will loose your warranty

rights. Do not use fuel mixtures that have been stored

for more than 90 days.

ATTENTION : Only use high-quality 2-stroke mixing

oil for air-cooled engines, mixture ratio 40:1.

FUEL MIXTURE

Mix the fuel with 2-stroke oil in an approved container.

Refer to the mixing table to nd the required mixture ratio

for the fuel and oil. Shake the container to properly mix

the two uids.

Mixing table for fuel mixture

Petrol 2-stroke oil / 40:1

1 litre 25 ml

5 litres 125 ml

ATTENTION : If you should you use an improper

mixture ratio you will loose your warranty rights.

STARTING THE ENGINE

Cold start

In order not to overtax the engine when starting it, cut the

trimmer cord to 17 cm (Fig. 7).

1. Put the ignition switch in position ‘I’ (Fig. 8).

2. Slide the choke to position ‘Start’ (Fig. 9). This is not

required in case of a warm start.

3. Push the fuel pump (A) 8 times (Fig. 10).

4. Pull the starter rope 2-3 times (Fig. 11); to start the

motor it is required to evenly, quickly pull the rope.

5. Slide the choke to ‘RUN’ position (Fig. 12), slightly push

the throttle lever (9) and pull the starter rope again until

the motor starts running. (To push the throttle lever (6)

it is necessary to rst push the locking lever (8) (g.

13).

6. Let the motor idle for about 10 seconds to warm up.

7. If the motor does not start repeat the steps 1-6.

NOTE:If the engine should not start after several

tries proceed as described in the chapter ‘Trouble-

shooting’.

NOTE : Always pull out the starter rope straight. If you

do not pull straight the rope will chafe at the eyelet. This

chafe will cause the rope to fan out and thus to a higher

wear and tear. Always hold the starter rope handle when

the rope is pulled back. Do not let the rope ick back

when it is pulled out. This could lead to a hook-up of

the rope and/or a damage to the starter housing.

STOPPING THE ENGINE (Fig. 14)

Release the throttle lever. Let the engine idle. Push the

ignition switch to position “Stop”. The motor will now stop.

Emergency stop: If it should be necessary to stop

the tool immediately push the “STOP” button.

OPERATING ADVICE

- If you are not familiar with the trimmer train the handling

of the device with the engine not running (AUS / OFF).

- Always check the territory; solid objects as metal parts,

bottles, stones etc. may be hurled away and cause serious

injuries or permanently damage the device. Should you

touch a solid object with the trimmer shut the engine off

immediately (AUS / OFF) and examine the trimmer for

possibly existing damages. Do not use the device when

it is damaged or shows sign of defects.

- Always trim and cut with the engine running in the higher

speed range. Do not let the engine run at low speed at

the beginning of or during the trimming.

- Use the device for its provided purpose only, i.e., trimming

and cutting grass and weeds.

- Never hold the cutting head higher than your knees during

operation.

- If working on a slope always stand with the cutting unit

above you. Only work on sloping sites if you stand on rm

ground.

TRIMMING

The trimmer – properly equipped with protection cover and

cutting head – trims high grass, brushwood and weeds

at places that are difcult to access along fences, walls,

foundations and around tree trunks. The trimmer may also

be used for cutting down to the ground (e.g., clean-out works

in the garden and in broken, thickly covered areas).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hanseatic XL 25 T in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hanseatic XL 25 T Manual

Product: