Manual Hanseatic XL 25 T (page 31 of 40) (English, German, French, Italian)

519139

Zoom out

Zoom in

1/40

GB-3

5) Make sure that you use the right fuel or petrol/oil

mix (lubricated petrol). To operate the device

the tank cap must be closed tightly.

6) Start the device at least three meters away from the

place where you fuelled it. Do not smoke during

fuelling or operation and take care that no sparks

or open ames reach into the working area.

DURING OPERATION

• Use this trimmer for its provided purpose only, i.e.

for the cutting of grass, brushwood and weed.

• Avoid any inadvertent starting of the engine. Make

sure, that the control lever is always in ‘Start’

position when you pull the starter rope.

• Always be attentive. To protect yourself and others

from injuries you should not work with this device

if you are tired.

• Do not work with this device under the inuence

of drugs, alcohol and medical drugs.

• Always wear protection goggles when operating

this device.

• Wear appropriate clothes. Do not work with this

device with bare feet or open sandals. Always wear

robust footwear with rubber soles. We recommend

to wear gloves, ear protection and long trousers.

• Do not wear wide clothing or scarves, chains, ties

etc. These may get sucked into the air inlet. Do

also take care that long hair does not get into the

air inlet. Tie long hair together behind the head so

that the neck and shoulders remain free from it.

• Keep your hands, face and feet away from any

moving parts. Do not try to touch or stop the cutting

cord as long as it is turning.

• Use this device in well-ventilated outdoor areas

only. In closed rooms, exhaust gases containing

carbon monoxide may have fatal effects.

• Do not bend forward too far. Always take care to

have a safe stand and good balance.

• Do not touch the exhaust pipe or cylinder. These

parts get extremely hot during operation and

stay hot for some time after the device has been

switched off.

• Always hold the trimmer with both hands during

work. Hold on to both the front and back handle

tightly.

• Check the condition of the cutting head regularly.

All damaged parts must be replaced immediately.

Follow the necessary safety measures when

replacing any parts.

• If you touch an object or get caught (with the

device) switch off the engine immediately and

check the device for possible damage. Repair

possibly existing damages before you try to

continue your work. Do not operate the trimmer if

it has loose or damaged parts.

• Do not run the engine faster than required for

cutting, trimming or the clean-cutting of edges. Do

not let the engine run on high speeds when you are

not cutting.

• The cord protection cover must always be mounted

when the trimmer is operated. If this should not be

the case, the engine may overheat. OPERATE THE

DEVICE ONLY WITH THE PROTECTION COVER

MOUNTED.

• The cutting diameter must not exceed the length

of the protection cover stated in this manual.

• Make sure that the trimmer is not soiled by parts

of plants or other materials.

• Always switch the engine off if you make a break

or move to another area.

• Replace the exhaust pipe and (if necessary) the

spark protector if these are not in proper working

order any more.

• To keep the danger of re as low as possible the

engine and exhaust pipe must be free from grass,

leaves and excess grease.

• For any interventions, whether maintenance or

repair works, the changing the cutting head or

installation of safety devices, the engine must be

switched off.

• Use original spare parts only. These parts are

available from your appointed retailer. The use

of deviating parts or other parts, accessories or

attachments that are not designed for this trimmer

may result in serious injuries to the persons using

it and your warranty will become void.

• Only use the trimmer with the right trimming cord

installed and with both trimming cords being at the

right length.

AFTER OPERATION

• Clean the trimmer from remainders of grass and

dirt after use.

• Lock the device in a proper place to protect it from

unauthorised use.

FURTHER SAFETY INSTRUCTIONS

• If there is still fuel in the device’s tank do not store

it in a building where the vapours may be ignited

by open re or sparks.

• Let the engine cool down, before you store the

device in a closed room.

• Lock the trimmer in a proper, dry room to protect

it from unauthorised use and damage.

ASSEMBLY

ASSEMBLY OF THE HANDLE (Fig. 1)

The petrol trimmer is tted with an additional handle. You

can adjust this handle to achieve a convenient working

position:

Remove the lower handle bracket from the included ad-

ditional handle. Put the lower handle bracket to the shaft

(from below) and put the additional handle on the shaft

exactly aligned with the bracket (from above). Connect

the two parts with each other using screws. Position the

handle according to the arrow – see warning label (B)

(Fig. 1). Tighten the screw rmly.

ASSEMBLY OF THE CORD PROTECTION COVER

(Fig. 2+3)

The protection cover must lock tightly into position at the

tube. It may be required to strongly push it into position.

1. Put the protector (B) on the shaft mounting (C).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hanseatic XL 25 T in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hanseatic XL 25 T Manual

Product: