624753

Gude TKGS 1800 Manual

19
Zoom out
Zoom in
Previous page
1/152
Next page
GB
19
Qualification
No special qualification is required for use of the
unit except for detailed direction by a
professional.
Minimum Age
Only persons above 16 years of age are allowed
to work with the unit.
Exempted from the provision is the use of the
juvenile trainees if they work in the course of
their professional training with an aim to obtain
the skill under trainer supervision.
Training
Use of the unit requires adequate lesson by a
professional or the use of the manual only .
Special training is not required.
Technical Data
TKGS 1800
Supply connection :
230 V/50 Hz
Max. output
1800 W/P1
Motor speed:
4800 min
-1
Protection type:
IP 33
Protection class:
II
Saw blade diameter/teeth :
250 x 20 mm/60 teeth
Max. cutting depth at 0°/0°
20 x 175 mm
Max. cutting depth at 45°/45°
50 x 120 mm
Max. cutting depth at 45°/45°
30 x 120 mm
Max. cutting depth at 45°/45°
50 x 115 mm
Weight ca:
32 kg
Dimensions L x W x H (mm)
800 x 630 x 820
EAN:
4015671 551700 2
Ordering No. : 55170
Transportation and Storage
• The unit should be cleaned thoroughly for a
longer storage. .
• Always push the blade in before putting the
unit on storage to avoid accidents.
• Protect the saw with a plastic cover,
cardboard etc. from weather effects.
Assembly and Initial Operation
(Fig. 2+3+4)
Turn the main element (Fig. 2) backward, feet
may be put in the working position in an easier
way then.
The lock screws (Fig. 3/4) to be loosened so that
the feet may be lifted out.
Then, tighten the screws to fasten all the four
feet.
Now, put the main element in the vertical position
again.
Use as a bench circular saw
(Abb. 4+5+6+78+9+10+11)
To use the saw as a bench circular saw, press
the lever (Fig. 4) down and turn the bench
around until a click is heard.
Now, loosen the butterfly screw (Fig. 6) with
which the splitting wedge is affixed.
There are two grooves of the splitting wedge
attachment cylinder (Fig. 6), therefore, two
setting-up options exist.
Press the saw handle lever locking the blade
guard (Fig. 7), push the blade guard up and
place the splitting wedge according to, fit in the
butterfly screw again.
Caution, always make sure to see that the
distance of the splitting wedge from the blade
is sufficient.
Screw in the screw (Fig. 8) to the stop so that the
saw is tilted down.
Press the lever (Fig. 9) down and turn the bench
around until a click is heard.
Pressing the knob (Fig. 10) on the blade guard,
the blade may be attached to the splitting wedge.
If dust extraction facility is not used, connect a
dust-collecting bag under the table to an outlet.
The mitre cut (Fig. 11) or the parallel stop (Fig.
11) to be fitted according to (Fig. 11) .
The saw is now ready for the bench mood.
Use as trimming or mitre saw
(Fig. 9+13+15+16+17+18)
To use the saw as a trimming or mitre cutting
saw, press the lever (Fig. 9) to unblock the
bench. It may be folded up then. With the turning
completed, the bench should be heard to click.
Push the orange knob (Fig. 13), turn it and let it
sink into the position. Now, put the saw unit in a
vertical position.
Caution
Enable the depth limiter with the lever (Fig. 14).
Caution
Change the splitting wedge position using the
butterfly screw (Fig. 15). The splitting wedge
should be put backwards so that the position of it
is in parallel to the blade, see (Fig. 16). To do
that, the opposite groove is used, see „Step 5
Use as a bench circular saw“.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude TKGS 1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude TKGS 1800 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info