624753

Gude TKGS 1800 Manual

20
Zoom out
Zoom in
Previous page
1/152
Next page
GB
20
Caution
Tighten the height changeover screw completely
(Fig. 17), turn it right completely, (a position
opposite to that in the bench mood)
Fit the chips guard for the trimming and mitre
mood according to the figure under the rotary
bench (Fig. 18). The chip guard is to be hung in
two eyes on the saw bench and than screwed on
at the opposite side with two screws attached.
(Fig. 19). If no extraction facility is used, connect
a chips collecting bag to one of the extraction
outlets. .
Now, the saw is ready to work in trimming
and mitre mode.
Operation
Unplug the unit before any setting of the
saw
Cutting Angle Set-up (Fig. 20+21)
• The blade adjustment 0° - 45° may be read
on the scale. By loosening the lock lever
(Fig. 20) and tilting the saw, the cutting
angle may be changed.
• The blade adjustment may be changed by
loosening the screw (Fig. 21) and turning
the saw.
Unit Switching on/off
• Press “green button I” to switch the unit on. .
• Press “red button 0” to switch off.
There is an emergency switch on the machine.
Longitudinal Sections
• Se the parallel stop at the required width in
relation to the blade.
Put the piece to be worked on the bearing
area, the wider/flatter end should be seated
on the saw bench flat wise
Caution: Keep the safety distance from the
blade.
Chamfer Cuts
• Fasten the piece to be worked according to
the figure using a clamp.
• Loosen the lock lever and set up the
required angle.
• Be careful to have the splitting wedge
aligned with the blade at any time.
• Secure the lock screw again.
• Switch the machine on, press the saw down
carefully and cut.
Cross Sections
• Insert the transverse stop into one of the two
grooves of the bench and set up the required
angle.
• Switch the machine on and use the
transverse stop to move the piece to be
worked to the rotating blade carefully.
Caution: Always hold the piece firmly,
never cut a piece held loosely
Splitting Wedge Set-up (Fig. 17+25)
• Loosen the screw on the splitting wedge
(Fig. 25), so that the wedge may be shifted
according the given type of the cut.
• Tighten the screw again.
Maximum cuts:
The distance between the bench and the splitting
wedge upper edge ca 10 cm.
Dovetail cuts:
The splitting wedge point 2 mm below the saw
tooth upper point.
The distance between the splitting wedge and the
blade 3-8 mm.
Dovetail Sections
• Move the splitting wedge down so that the
splitting wedge point is 2 mm below the top
point of the saw tooth.
• The distance between the splitting wedge
and the blade should be 3-8 mm again. .
• Insert the transverse stop into one of the saw
bench groove and set up the required angle.
• If the blade is to be adjusted askew as well
the groove preventing contact of your had
and the transverse stop with the blade guard
should be used as well.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude TKGS 1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude TKGS 1800 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info