633026
9
Zoom out
Zoom in
Previous page
1/16
Next page
9
7.0 - RAPID TEST
WARNING:
- Ensure that the alarm is disarmed.
A - Earth the GREEN/YELLOW wire until the alarm system emits a long acoustic signal and
the LED BUTTON starts flashing.
B - After about 10 seconds the alarm system will emit 3 visual (indicators)/acoustic signals
and it will enter automatically the RAPID TEST function. The alarm system can be considered
correctly installed if:
1 - The PINK wire has a positive signal (+12V) output and the additional sensors/modules
connected to this wire activate.
2 - When opening one of the doors (GREEN/BROWN or GREEN/BLUE wires) and the bonnet/
boot (GREEN wire) you will obtain a visual (indicators)/acoustic signal.
3 - When you activate an additional sensor (GREEN/BLACK wire) you will obtain 2 flashings
of LED BUTTON and a visual signal (indicators).
4 - When you activate the ultrasonic sensor you will obtain a visual signal (indicators).
To test the alarm, remove all possible items that may create movements and ensure that
doors and windows are closed. Introduce your arm through the gap and move it around; the
alarm system indicators will flash to confirm correct operation. To increase the sensitivity, turn
the adjuster close to the main alarm connector clockwise (see page 4).
Warning: this procedure is one of the most important correct alarm operation. To check tthe
sensitivity, move your arms across the outside of the window and the soft top roof, this should
not trigger the alarm. Only the introduction of an object should trigger the alarm.
5 - If you press the ANTI-HIJACK FUNCTION reservation button (BLACK/WHITE wire) you
obtain a visual (indicators)/acoustic signal.
6 - When the ignition key is ON you will obtain an acoustic signal (if an additional GT 843
siren is connected, this will sound for about 1 second).
6 - Unlock the vehicle using the original remote control, after a couple of seconds the alarm
will emit 2 visual signals (indicators), and 3 acoustic signals indicating the end of self coding
and the doors will unlock.
Warning: The procedure can be considered carried out correctly only if the operations are in
compliance with the points 5 and 6. On the contrary wait that the alarm system comes out
automatically from the procedure (the alarm system will emit an acoustic signal).To repeat
the procedure disconnect the positive leave for a few seconds and then reconnect. Start the
procedure again from point 1.
Note: supposing that the self-coding procedure has been completed correctly, but you want
to repeat it, for example in the case of the alarm command wires connection (i.e. RED/BROWN,
YELLOW/BROWN, RED/GREY AND YELLOW/GREY wires) has to be changed, it is
necessary to repeat the signals self-coding procedure from the point 1, remember to
disconnect the alarm system power supply for some seconds.
If a self-coding procedure hasn’t been correctly carried out the system can only be
disarmed by the “GT CARD CODE” (see the relative section). Once the alarm is
disarmed, proceed with the self-coding before using the original vehicle’s remote control
handset.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 800-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 800-2 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info