633026
7
Zoom out
Zoom in
Previous page
1/16
Next page
7
LED BUTTON
CONDITION
The DEFAULT
programming are in “bold”
ALARM SYSTEM
FUNCTION
NUMBER OF
PRESSES
OF THE LED
BUTTON
NUMBER OF
LED BUTTON
/LED FLASHES
FOR THE
FUNCTIONS
STATUS CHECK
LED OFF LED ON
Self-coding indicators
impulses number
1 1
Disabled
Enabled
Switches/Discriminators
signals stabilizer
2 2 Deactivated
Activated
Memorisation of
switches/discriminators
signals only after actuator
signals
3 3
Disabled
Enabled
Memorisation of actuator
signals of changeable type
4 4 Disabled
Enabled
Anti-hijack door signal
stabilizer
5 5
Deactivated
Activated
Acoustic signal when
arming/disarming the alarm
system
6 6 Deactivated
Activated
Visual signal when
arming/disarming the alarm
system
7 7
Deactivated
Activated
Courtesy light switching on
when disarming
8 8
Deactivated
Activated
To modify the settings proceed as follows:
1 - Press the LED BUTTON the number of times corresponding to the function you wish to
check or modify. The alarm generates an acoustic signal for each press.
Before showing the function state, the alarm system will generate acoustic signals and the
LED BUTTON will flash. For example: if you wish to check the function state “Acoustic signal
when arming/disarming the alarm system”, you will have to press the LED BUTTON 6 times,
check that it flashes 6 times and the LED BUTTON remains switched on (acoustic signal
activated) or switches off (acoustic signal deactivated).
2 - When the LED BUTTON shows the function state you are checking (the LED BUTTON
switched on or off), it is possible to modify the alarm system function condition by pressing
the same LED BUTTON.
3 - Once the function state has been selected, the LED BUTTON will flash to indicate that the
new condition has been memorised. If the LED BUTTON isn’t pressed again, or the ignition is
switched off within 2 minutes, the alarm system comes out from the set condition automatically.
4 - At this point, the alarm system will emit a long acoustic signal to confirm you have come
out from the SET FUNCTIONS.
When the alarm system functions have been programmed carry out the DOORS LOCK/
UNLOCK SIGNALS SELF-CODING (page 8).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 800-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 800-2 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info