467107
158
Zoom out
Zoom in
Previous page
1/200
Next page
158
Program description: Trainer system
Wireless HoTT system
The mx-16 HoTT Trainer system can also be operated
by wireless means. In this case the Teacher transmitter
is “connected” to a Pupil transmitter as described in the
following section. However, the trainer model must first
be bound to the PUPIL transmitter. This configuration is
possible between transmitters which feature the “BIND:”
option in the Trainer” menu.
Preparations for Trainer mode operations
Teacher transmitter
The trainer model must be programmed completely,
i. e. with all its functions including trims and any mixer
functions, in a model memory of the HoTT Teacher
transmitter. This means that it must be possible to
control the trainer model fully, without restriction, by
the Teacher transmitter. However, the preparations
are concluded by binding the training model to the
Pupil transmitter; you will find a detailed description
of the binding procedure on pages 80 and 88.
Pupil transmitter
If you are using an mc” or mx” series transmitter,
it is best to set up a free model memory in the Pupil
transmitter with the required model type (“Fixed-wing”
or “Helicopter”). Assign the model name “Pupil” to the
memory, and set up the stick mode (Mode 1 … 4) and
“Throttle min. forward / back” to suit the pupil’s prefer-
ence. All the other settings should be left at the appropri-
ate default values. If you select the “Helicopter” model
type, the throttle / collective pitch direction and idle trim
must also be set accordingly on the Pupil transmitter. All
other functions, including mixer and coupling functions,
are carried out by the Teacher transmitter, which trans-
mits them to the receiver in the model.
When assigning the control functions the usual conven-
tions should be observed:
Channel Function
1 Throttle / Collective pitch
2 Aileron / Roll
3 Elevator / Pitch-axis
4 Rudder / Tail rotor
If you wish to transfer further control functions to the
Pupil transmitter, i.e. in addition to the functions of the
two dual-axis stick units (1 … 4), then you will need to
assign transmitter controls to those inputs which cor-
respond to the function or transmitter control inputs 5
… 8, as selected in the Teacher transmitter’s “Trainer”
menu; this has to be carried out in the Pupil transmitter’s
Transmitter control settings menu.
Important:
If you should forget to assign a transmitter control
at the Pupil end, the servo or servos concerned
will remain at their centre position when control is
transferred to the Pupil transmitter.
Preparing the Teacher and Pupil transmitters
Once you have bound the trainer model to the Pupil
transmitter, the Teacher transmitter should also be
switched on. Now use the arrow buttons or the left or
right-hand touch-key to leaf through on both transmitters
to the “Trainer menu point in the multi-function menu:
servo set.
D/R expo
wing mixer
contr set.
phase trim
free mixer
servo disp basic sett
fail-safe
telemetry
info dispteach/pupi
servo set.
D/R expo
free mixer
contr set.
heli mixer
swashp.mix
servo disp basic sett
fail-safe telemetry
teach/pupi info disp
Touch the central SET button of the right-hand touch-key
to open the following menu point:
TRAINER/Pupil
–P
T
2 3
4
5
6
7 8
BIND:SW: –––
1
N/A
The illustration above shows the initial state of this
menu: no transmitter controls have been released to the
Pupil ( ), and no switches have been assigned (SW: ---
bottom right and -S on left of illustration).
Pupil transmitter
Use the arrow buttons of the left or right-hand touch-key
to move the marker / cursor to the input field marked
“Bind”. If a switch is displayed adjacent to “SW” on the
right, then it is essential to erase this: see the following
illustration:
158


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info