467107
156
Zoom out
Zoom in
Previous page
1/200
Next page
156
Program description: Trainer system
The Pupil transmitter must always be operated in •
PPM mode, regardless of the type of RF link be-
tween the Teacher transmitter and the model.
If the Pupil transmitter is connected using a DSC •
socket, then you should ALWAYS leave the Pu-
pil transmitter’s On / Off switch at the “OFF” posi-
tion, as this is the only way to ensure that the Pu-
pil transmitter module does not generate an RF
signal even when the DSC lead is plugged in.
Trainer mode operations
Connect the two transmitters using the appropriate
lead; see the overview on the next page: connect the
plug marked M” (Master) to the socket on the Teacher
transmitter, and the plug marked S (Student) (not
present on all leads) to the appropriate socket on the
Pupil transmitter.
Important notes:
It is essential to check that all functions are •
transferred correctly to the prepared model BE-
FORE initiating Trainer mode operations.
If you are using a Trainer lead with three-pole bar-•
rel connectors, on no account connect one of the
ends marked “S” or “M” to a DSC system sock-
et, as it is not suitable for this purpose. The DSC
socket is only suitable for leads fitted with two-
pole barrel connectors.
Checking the system
Operate the assigned Trainer transfer switch:
If the screen display changes from „• T“ to „P“, the
Trainer system is working properly.
However, if the central LED flashes blue / red at a •
high rate, and at the same time the transmitter emits
audible signals, then there is a problem with the con-
nection between Pupil and Teacher transmitter.
At the same time the following warning appears in
the base display …
no
student
signal
… and in the Trainer” menu the display changes to
“-P” on the left. If this should happen, note that all the
functions automatically remain under the control of
the Teacher transmitter, regardless of the position of
the Trainer transfer switch; this ensures that the mod-
el is not out of control at any time.
Possible errors:
Pupil transmitter not ready•
The interface in the Pupil transmitter, which replaces •
the RF module, is not connected correctly
Incorrect cable connection: see next section for cable •
selection
Pupil transmitter not set to PPM (10, 18, 24) mode.•
Further possible errors:
Teacher transmitter and HoTT receiver in trainer •
model not correctly “bound”.
Trainer leads
4179.1 For Trainer mode operations between any
two Graupner transmitters equipped with a
DSC socket - identifiable by two-pole barrel
connectors at both ends.
3290.7 Trainer lead for connecting a Teacher trans-
mitter with DSC socket (e. g. mx-16 HoTT),
or a transmitter retro-fitted with the option-
al DSC module, Order No. 3290.24, to a
Graupner Pupil transmitter with opto-elec-
tronic Pupil socket - identifiable by the letter
S at the end with the three-pole barrel con-
nector.
3290.8 Trainer lead for connecting a Pupil transmit-
ter with DSC socket (e. g. mx-16 HoTT)
or a transmitter retro-fitted with the option-
al DSC module, Order No. 3290.24, to a
Graupner Teacher transmitter with opto-elec-
tronic Teacher socket - identifiable by the let-
ter “M at the end with the three-pole barrel
connector.
For more detailed information about the leads and mod-
ules for the Teacher and Pupil transmitters listed on this
page, please refer to the operating instructions supplied
with your transmitter, the main Graupner FS catalogue,
or the Internet at www.graupner.de.
156


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info