Manual Graupner MX-16 HoTT (page 155 of 200) (English)

467107

155

Zoom out

Zoom in

1/200

155

Program description: Trainer system

NER / teacher” as soon as a switch is assigned.

The model to be controlled by the pupil must be pro-

grammed completely in a model memory of the mx-

16 HoTT Teacher transmitter, i. e. with all its functions

including trims and any mixer functions. The HoTT re-

ceiver in the model must also be “bound” to the Teacher

transmitter, since it is this transmitter which actually

controls the model in Pupil mode - even in Trainer mode

operations.

The mx-16 HoTT Teacher transmitter MUST ALWAYS

BE SWITCHED ON FIRST. ONLY THEN MAY THE

CONNECTING LEAD BE PLUGGED INTO IT. If you

neglect this, the RF module will not be activated.

The mx-16 HoTT Teacher transmitter can be linked to

any suitable Pupil transmitter - even those operating on

the “classic” 35 / 40 MHz band.

However, if the connection at the pupil end is NOT

made using a two-pole DSC socket, but instead - for

example - using a three-pin Trainer socket from the

Graupner range, the basic requirement for a correct

connection with a Pupil transmitter is that PPM (18

or 24) modulation must ALWAYS be set on the Pupil

transmitter, regardless of the modulation used by

the Teacher transmitter.

Pupil transmitter settings

The model to be controlled by the pupil must be pro-

grammed completely in a model memory of the Teacher

transmitter, i. e. with all its functions including trims and

any mixer functions, and the HoTT receiver in the model

must be “bound” to the Teacher transmitter. In principle,

however, an mx-16 HoTT Pupil transmitter can also be

linked to a Teacher transmitter operating on the “classic”

35 / 40 MHz band.

The Pupil transmitter can be virtually any transmitter

from the former and current Graupner range with at

least four control functions. More information on this is

available in the main FS catalogue, and on the Internet

under www.graupner.de.

Some transmitters will need to be retro-ﬁtted with the

appropriate module in order to act as the Pupil transmit-

ter. This should be connected to the transmitter circuit

board as described in the installation instructions sup-

plied in the set.

Information on the Pupil module required can be found

in the main Graupner FS catalogue and on the Internet

at www.graupner.de.

The Pupil transmitter must be connected to the Teacher

transmitter using the appropriate lead - see next double

page.

The control functions of the Pupil transmitter MUST

act directly on the control channels, i. e. the receiver

outputs, without the intervention of any mixers.

If you are using an “mc” or “mx” series transmitter,

it is best to set up a free model memory in the Pupil

transmitter with the required model type (“Fixed-wing”

or “Helicopter”). Assign the model name “Pupil” to the

memory, and set up the stick mode (Mode 1 … 4) and

“Throttle min. forward / back” to suit the pupil’s prefer-

ence. All the other settings should be left at the appropri-

ate default values. If you select the “Helicopter” model

type, the throttle / collective pitch direction and idle trim

must also be set accordingly on the Pupil transmitter. All

other functions, including mixer and coupling functions,

are carried out by the Teacher transmitter, which trans-

mits them to the receiver in the model.

If you are using an mx-20 or

mc-3 2 HoTT Pupil

transmitter, it is also necessary to match the type of

modulation to the numbers of the control channels to

be transferred; this is carried out in the “DSC output”

line of the “Basic model settings” menu. For example,

“PPM10” modulation carries control channels 1 … 5,

and its signal packet only contains control channels 1

… 5 - but not channel 6. If you also wish the pupil to be

able to use this channel, then you must select a type of

modulation which includes it!

If you are using a “D” or “FM” type transmitter, you

should check the servo directions and stick mode, and

alter them by re-connecting the appropriate leads if re-

quired. All mixers should be switched off or set to “zero”.

When assigning the control functions the usual conven-

tions should be observed:

Channel Function

1 Throttle / Collective pitch

2 Aileron / Roll

3 Elevator / Pitch-axis

4 Rudder / Tail rotor

If you wish to transfer other control functions to the

Pupil transmitter, in addition to the functions of the two

dual-axis sticks (1 … 4), then you will need to assign

additional transmitter controls in the Pupil transmitter’s

“Transmitter control settings” menu to those inputs

which correspond to transmitter control numbers 5 … 8,

as released in the Teacher transmitter’s “Trainer” menu.

Important:

If you forget to assign a transmitter control, then •

the servo or servos concerned will remain in the

centre position when control is transferred to the

Pupil transmitter.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MX-16 HoTT Manual

Product: