30117
7
Zoom out
Zoom in
Previous page
1/104
Next page
General Section 7
Power Supply
The battery tray in the transmitter is equipped with a
9.6v battery.
Different battery types are available to be selected.
Into the battery mounting for the receiver, insert four
AA cells of 1.2v and between 500 and 600mAh.
Instead of the battery mounting, or in addition, a 4.8v
battery with miniature plug can be used, see page 5.
Pay attention to the full battery voltage. If the rudder
moves noticeably more slowly or display the goes
under 9.6v back then stop operation and load new
batteries (or recharge).
Charger devices and batteries - see Graupner main
catalogue telex.
Your contribution to environmental protection:
Do not throw to used up batteries into the domestic
refuse, but take these to an appropriate collecting
point, in order for them to be recycled or disposed of
in an environmentally friendly way.
Charging of the Transmitter battery
The rechargeable transmitter battery can be charged
in the Transmitter using the socket on the side of the
case. The set must be switched OFF while charging.
When using the automatic MULTILADER 5B or 6E
the connection is made by charging cable Part No.
3022. For the MULTILADER 5 it is necessary to use
the polarised charging cable Part No. 3040.
The remote control system is equipped with a
reverse connection protection circuit for charging of
the Transmitter battery. Thus damage is prevented
by incorrect polarity or short-circuit. In order to
disable this reverse current protection (e.g. for
measuring purposes or when connecting an
automatic loader), it is necessary that the enclosed
two-pole plug link is attached directly to the link pins
as short circuiting bridge.
During rapid charging the transmitter battery
charging current must not exceed 1.5A.
Charging the receiver battery.
The charging cable Part. No. 3021 for
MULTILADERS 5B and MULTILADER 6E can used
to connect the receiver battery directly to the
charger. If the battery is in the model, then charging
cables Part. No. 3023, 3046, 3377, 3934 or 3934,3
are attached making use of the connector integrated
into the receiver switch harness. For the universal
battery charger MULTILADER 5 the polarised
charging cable Part. No. 3041 is necessary.
The period of operation of receiver batteries depends
heavily on the battery type and on the frequency of
servo movements and their load. In the PCM mode
the "Fail Safe" function can be activated, which will
display when the receiver battery falls below to a
certain voltage, see page 25.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC16 in the language / languages: English as an attachment in your email.

The manual is 16,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC16

Graupner MC16 User Manual - German - 68 pages

Graupner MC16 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info