467111

Graupner MC 32 HOTT Manual

72
Zoom out
Zoom in
Previous page
1/345
Next page
72 Program description - Loading a new memory location
Model name
Stick mode 1
n/a
BASIC SETTINGS MODEL
Info
n/a
n/a
Module bind
HoTT
SEL
If this setting is desired as a default for future models,
the setting can also be entered into the »General
basic settings« menu, page 276:
Owners name
Pre-set stick mode
Pre-set DSC Output
1
GENERAL BASIC SETTINGS
PPM10
SEL
Pre-set modulation HoTT
It should be noted here once again that, in the interest
of greatest flexibility in combination with the prevention
of unintentional operating errors, no controls are preas-
signed to control channels 5 … 16 by default.
This means that, in the system's delivered
state, only servos attached to receiver
outputs 1 … 4 can typically be operated by
the two sticks and that any servos attached to
receiver connectors 5 … 16 (max) will remain in
their middle positions.
Firmware version V1102 and lower
A newly initialized helicopter model is also able to
more-or-less move servo 6 – depending on the posi-
tion of the right-side proportional rotary slider, which
is the default throttle limiter control.
Firmware version V1102 and higher
A newly initialized helicopter model is also able to
more-or-less move servo 6.
With either model type, this situation will only change
after appropriate assignments have been made in the
»Control adjust« menu.
On the other hand, if a newly initialized model mem-
ory is to be put into operation then it MUST first be
appropriately "connected" with one or more receivers
before the servos attached to the receiver/s can be
operated. More about this can be found in the section
"Binding" on page 118 or 122.
A fundamental description of programming steps for
a winged aircraft model can be found in the program-
ming examples section beginning on 288, or for heli-
copter models beginning on page 328.
The menu descriptions below are arranged in the
sequence individual menus are listed in the multi-
function list.
… 72 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info