467111
73
Zoom out
Zoom in
Previous page
1/345
Next page
73
Program description - Model select
Model select
Call up model 1 … 80
The basic operation of the transmitters keys was
explained on pages 30 and 31 and, on the previous
double-page, explanations were provided for navigat-
ing to the multifunction list and about how to make
allocations for a new model memory. At this point we
now wish to begin with the "normal" description of
individual menu items in the sequence they are ar-
ranged in the transmitter. Therefore we will begin with
the menu …
Model select
Servo adjustment Stick mode
Control adjust Dual Rate / Expo
Channel 1 curve Switch display
Model select Copy / Erase
Suppress codes Suppress models
Base setup model Model type
Model select
Servo adjustment Stick mode
Control adjust Dual Rate / Expo
Channel 1 curve Switch display
Copy / Erase
Suppress codes Suppress models
Base setup model Model type
Select the »Model select« menu with the selection
keys of the left or right touch pad then briefl y tap on
the SET key of the right touch pad.
Note:
Firmware V109x to uncluded V1100
Attention!
Switch-OFF
the Receiver first!
If this message appears, there is a telemetry link to a
receiving system operational.
Turn off this.
Firmware from V1101
If the currently active model “Global” bound, a model
change is only possible after switching off the receiv-
ing system for safety reasons:
Attention!
Switch-OFF
the Receiver first!
If the currently active model memory bound specifi -
cally, a model change is now possible without the
need to switch off the receiving system:
03
04
Ultimate
02 00:44hR12
Starlet
BELL47G
00:33hR08
00:22hR08
Test
trim needed
 free
 free
05
06
01 01:23hR16Graubele 1234g/080811
As many as 80 complete model settings, including
digital trim values for the trim wheel, can be stored.
Trimming is stored automatically such that a switcho-
ver from one model to another does not cause a
loss of current trim settings. To the right of the model
number, each occupied model memory line in this
display shows a pictograph of the model type as well
as the model’s name entered for the model in its
»Basic settings, model« menu, page 76 or 84. The
code, if present, for the receiver “bound” to the model
memory location will appear right in the line.
Now, with the  selection keys of the left or right
touch pad, select the desired model memory from the
list and activate it with a tap on the SET key. A tap on
the ESC key will cause a return to the previous menu
page without activating a model change.
Notes:
If, after a model change, the "Throttle too
high" warning appears, the throttle/pitch
stick (C1) or the throttle limiter by default,
the right-side proportional rotary slider is too far
in the full throttle direction.
If a model change causes the message …
BIND. N/A
OK
… to appear then binding settings should be
checked.
If a model change causes the message …
Fail Safe
setup
t.b.d.
… to appear then respective failsafe settings
should be checked.
If battery voltage is too low, the model switchover
cannot be made due to reasons of safety. An
appropriate message will appear in the screen:
not possible now
voltage too low
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info