467111

Graupner MC 32 HOTT Manual

71
Zoom out
Zoom in
Previous page
1/345
Next page
71
Program description - Loading a new memory location
• After the selected model memory is initialized with
the desired model type, the display will switch to
the base screen of the freshly occupied model
memory. At this time the warning …
BIND. N/A
OK
… will appear for several seconds as noti cation
that a binding connection to a receiver is "not
available". A brief tap on the centre SET key of
the right touch pad will cause a direct jump to the
appropriate option.
Model name
Stick mode 1
n/a
BASIC SETTINGS, MODEL
Info
n/a
n/a
Module bind
HoTT
SEL BD1 BD2 BD3 BD4
Further details about binding a receiver can be
found on page 84 or 94.
• At the right and above the aforementioned "BIND.
N/A" warning message, the warning …
Fail Safe
setup
t.b.d.
… will appear (also for just a few seconds) to
indicate that no fail safe settings have yet been
made. More about this can be found on page 224.
• If the screen should display the warning …
Throttle
too
high!
Afterward you will be prompted to select the basic
model type, i. e. either "winged model" or "helicopter
model".
Select model type ( free model memory )
Use the or keys of the left or right touch pad to
select the basic model type then tap on the centre
SET key of the right touch pad. This initializes the
selected model memory with the selected model type
and the display will return to the base screen. The
memory location is now accordingly occupied.
Changing over to another model type is still possi-
ble if you fi rst erase this memory location (»Copy /
Erase« menu, page 74).
Notes:
• If the currently active model memory is to
be erased then immediately after the erase
action one of the two model types,
"Winged" or "Heli" must be de ned. You cannot
avoid this selection even if you switch the
transmitter off. When the transmitter is switched on
again the undesired occupation of the that model
memory will have to be erased from another
memory location.
If a non-active memory location is erased, it will
subsequently be marked as "free" in the
"Model select" menu.
… then move the throttle stick, or the limiter for a
helicopter, (by default this is the right rotary slider
Lv1) into its idle position.
Whether or not this warning appears also depends
on the settings selected for the "Motor on C1" and
"Pitch min." options in the »Model type« menu,
see page 104, or »Helicopter type« menu,
see page 108. For winged aircraft models, select
"None" to deactivate this message if you have no
motor
to enter.
• If the transmitter already has occupied model
memories then sub-menus of the »Copy /
Erase« menu will display a pictograph of the
selected model type at the respective memory
location followed by a blank line or the model
name which was entered in the »Basic
settings, model« menu, page 82 or 92. To
the right of this will be as display of the model
operating time and, if present, "Info" about the
model.
• If battery voltage is too low, the model switchover
cannot be made due to reasons of safety. An
appropriate message will appear in the screen:
not possible now
voltage too low
As a basic principle, there are four different ways to
assign the four control functions, aileron, elevator,
rudder and throttle or brake fl aps for winged models
as well as rolling, pitching, tail rotor and throttle/pitch
for helicopter models, to the two sticks. Just which of
these methods is used depends on the preferences of
the individual model pilot. This function is set for the
currently active model memory in the "Stick mode"
line of the »Basic settings, model« menu, page 82
or 93.
… 71 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info