467111
22
Zoom out
Zoom in
Previous page
1/345
Next page
22 General operating notices
Holder bracket for transmitter straps
A stable transmitter hanger for fastening neck straps
is standard equipment on the mc-32 HoTT trans-
mitter.
To unfold the holder brackets, fi rst press both brack-
ets inward a bit near where they are lettered then turn
them upward by 90 °. The brackets will automatically
lock into position.
If you have a neck strap fastened to the holder brack-
et with key-rings, fi rst press lightly on the right holder
bracket to release its latch so it can be folded down
then do the same with the left holder bracket. After-
ward, press both brackets SIMULTANEOUSLY into
the recess.
The following straps are available as accessories:
No. Description
71.26 Transmitter straps, Graupner HoTT
72.40 Transmitter straps, deluxe
Installation of switches, switch modules and knob
modules
There are a total of 20 holes in the transmitter's hous-
ing available for mounting accessory modules.
ATTENTION:
To be safe, always disconnect the transmitter
battery before installation to avoid short cir-
cuit conditions. Be sure to pay attention that
soldered points on the transmitter board do not come
into contact with metal objects!
Unoccupied holes in the transmitter's housing are
closed with blind plugs. These can easily be pulled
out from the outside with one's fi ngernails.
Insert the accessory switch, etc. through a hole in the
housing from the inside.
Accessory switches, potentiometers, etc. are fastened
into place by screwing a nut onto the threaded shaft
protruding though the housing and tightening it with
a suitable wrench. If the control has a knob, it can be
reattached after the nut is tightened down. Trim nut
wrench (No. 5733) is well suited for tightening down
these nuts.
Trim nut wrench (No. 5733) is well suited for
tightening down switch element trim nuts.
Aligning the antenna
The removable, articulated antenna is to be screwed
into the ball-joint connector then aligned by hand.
The antenna exhibits very limited fi eld strength
straight out from its end, pointing it directly toward the
model is wrong.
ATTENTION:
When screwing in the antenna, pay attention
that the centre pin in the antenna socket does
not get bent or pressed back in the socket.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info