467111
24
Zoom out
Zoom in
Previous page
1/345
Next page
24 Transmitter description - Face-side connections
display of telemetry data and symbols will be
suppressed.
#01 0:00h
Stop watch
Flight tim
K78
0:00.0
4.1V
0:00.0
00
0
0
0:00h
DSC
The transmitter's upper display will show the
message "CANNOT RECEIVE DATA" during this
time.
Thus the transmitter is ready for operation.
In contrast, the mc-32 HoTT transmitter
in teacher mode is to be switched on prior to
plugging in the respective cable.
3. Connect the other end of the cable to the desired
unit in compliance with the given operating
instructions for that unit.
Important:
Pay attention that all plugs are inserted
securely into their respective sockets
and use only the prescribed 2-pole TRS
connector plugs on the DSC-side.
4. In the line "DSC Output" in the »Basic settings,
model«, page 89 or 100 or the line "Pre-set DSC
Output" in the »General basic settings«, page
277, depending on the number of functions
transferred one of the following modes can be
set: PPM10, PPM16, PPM18 or PPM24. Default
setting: PPM10.
Notice about  ight simulators:
Because of the myriad of  ight simulators
available on the market, it may be
necessary to have the contact layout of
the audio plug or DSC module appropriately
modi ed by Graupner Service.
DSC / Direct Servo Control
The acronym "DSC" is a carryover which stands for
the original "Direct Servo Control" function. However,
in HoTT systems the "direct servo control" function is
no longer available via a diagnose cable due to tech-
nical reasons.
Once the left face-side cover has been moved away,
the mc-32 HoTT transmitter's DSC socket is ac-
cessible:
The standard two-pole DSC jack in the mc-32
HoTT transmitter is used as the teacher or pupil jack
as well as an interface to fl ight simulators or external
RF module.
To ensure a proper DSC connection, please observe:
1. Make any necessary menu changes.
Refer to the section beginning on page 226 to
adapt the mc-32 HoTT transmitter to a teacher/
pupil system.
2. When operating a fl ight simulator or when
operating the mc-32 HoTT transmitter as a
pupil transmitter, ALWAYS leave the transmitter's
ON/OFF switch in the "OFF" position as only in
this position does the transmitter's RF module
remain inactive after the DSC cable is inserted.
This also reduces the transmitter's power
consumption somewhat.
Only the "
Battery
" LED should remain
constantly illuminated and the transmitter's basic
display should show the character string "DSC"
below the operating time clock. At this time, the
Face-side connections
Charger jack
The mc-32 HoTT transmitter's charger jack be-
comes accessible after turning the left face-side cover
away.
The transmitter's rechargeable LiIo battery can be
charged by way of the charger socket located behind
a cover on the left, front side of the transmitter as
viewed from the front with the included plug-in
charger (No. 32032.4).
Maximum permissible charging current with Graupner
automatic chargers: 1.5 A.
Never use plug-in chargers from other manufacturers
or chargers intended for other battery types. Charger
output voltage which is too high or possibly even
different plug polarity, see further below, can cause
immense damage.
More information about charging the transmitter's
battery can be found on page 18. Observe the safety
notices on pages 8 … 10 when handling lithium bat-
teries.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info