637250
10
Zoom out
Zoom in
Previous page
1/20
Next page
10 - 20
GR-10C_jh_V1
Transmitter pre-settings
In the transmitter it must be selected a free model memory, the
model type must be “surface model“ and the channel 1 direction
must be set so that in “motor off“ position the power indicator
must show -100%.
The flight mode must be set on channel 5. For this program a
2-way switch (eg switch 3) in the transmitter control menu on
Channel 5 as follows:
Attitude mode: Channel 5 = -100% to +50%. The stick move-
ment determinates the Copter reaction on Roll and Nick. It
allows a maximal angle of about 50° at 100% of stick move-
ment. Mode suggested for beginners. The stick movements
acts directly proportionally to Roll and Nick.
Rate mode: Channel 5 = more than +50%. The stick movement
determinates the rate without angle limit. Aerobatic mode that
allows rolls and loopings.
We suggest to set the fail-safe on channel 5 and channel 1 at
-100% , so that in fail safe it is active the attitude mode.
Program always the motors stop switch on the transmitter. (See
transmitter manual) This prevents accidental starting of motors,
thus reducing the risk of injury.
In Acro 3D Mode: In addition to the motors stop switch you need
to program a mixer to be able to switch the motors off in 3D
Acro mode too. If the 3D Acro mode enabled and you control
over the rate mode, the motor stop function would control the
motors fully backward. To prevent this, the mixer switches to
attitude mode, here then the stopping of the motors is ensured
via the switch. Set a free mixer from S1 to CH5. (see display
screenshot on the left)
Switching function channel 7 and 8
Both ports 7 and 8 in the receiver can be used for switching
accessory functions. Through them you can e. g. switch on and
off LED lights. In the port is available the receiver voltage when
the channnel is switched on. Here it is switched the minus, plus
is always on. For this program a 2-way switch in the transmitter
control menu on channel 7 and 8 with the following values:
-100% to +50% = Switch function off
> +50% = Switch function on
Attention
Max. switch current channel 7 = 2A, channel 8 = 1A
Observe the correct port polarity (see figure below)
Step 1
Setting of the flight-mode -
attitude or rate mode
E5
– trv +
+100%
E6
+100%
+100%
+88%
+100%
free
3
Do not forget to set the failsafe up!
Program motor-off switch!
Ty p
fro
zu
M1
M2
M3
S
5
??
??
M4
M5
??
??
??
??
??
??
1
=
to
MIX 1
trv +100%+100%
Offset
ASY
SYM
S 5
+100%
Mixer motors stop with channel 5
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-10C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-10C in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info