637250
11
Zoom out
Zoom in
Previous page
1/20
Next page
11- 20
GR-10C_jh_V1
Initialization of the gyro
Once the model has been switched on, the gyro immediately
becomes active but still needs to be initialised. To initialise the
gyro, keep your model still when you switch it on. The calibra-
tion process can only be performed when the receiver is abso-
lutely still. After 3 seconds in still position you will hear beeps
emitted by all motors. The signal tone can vary depending on
the esc model. These "wiggles" signal that initialisation has been
successful and that calibration is complete. Always wait until the
calibration process has finished before starting to fly the model.
The motors will not start until the calibration is complete.
CAUTION
If the copter is used for long time (>1min) in Acro 3D mode the
receiver can loose its position information and the copter can
move itself out of control. Before switching back to Attitude
mode, hoover the copter for 30 s or land it in Rate mode, so that
the receiver can reset the position.
Special function channel 6
The auto-flip function allows you to flip your copter in a very easy
way. It is essential that you control in Attitude mode (function not
allowed in Rate mode).
The auto-flip function must be controlled by channel 6. For this
program a 2-way switch (e. g. SW1) in the transmitter control
menu on channel 6 with the following values:
Auto-flip function on = Channel 6 > 110%
Auto-flip function off = Channel 6 < 110%
Activate the switch and within 5 sec move the nick or roll stick
to more than 50% of its course, then the copter makes auton-
omously a flip in the selected direction. After the flip it is possible
to have some little position movements (<10°)
Basic settings
Type
Quadro x, Quadro +, Tri L, Tri R
Channel connections to the receiver for the different copter
types.
Connect the speed controllers of the motors to the receiver fol-
lowing the proper scheme (see next page "Connection scheme
of different copter types").
In case of tricopter use only digital servos for servo 4.
Motor direction seen from the top of the copter!
Initialization by switching on
!
Step 2
Basic settings
Multicopter Basis< v >
>Type Quadro X
Mode NORMAL
ONESHOT No
Minpower % 10
Calibr. Posit. No
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-10C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-10C in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info