637250
9
Zoom out
Zoom in
Previous page
1/20
Next page
9- 20
GR-10C_jh_V1
Telemetry or channel (T/9) socket
The optional telemetry sensors are connected to the socket
marked “T” (T/9)- Telemetry. In addition, the update is performed
on this socket. The socket can even be used as optional chan-
nel 9. (see following section)
Power supply
Connect the power supply to the battery port.
Make sure that the polarity is correct!
The input voltage should not be higher than 8,4V. (1 -2 S)
Receiver setup menu
The receiver setup menu appears in the “Telemetry“ menu under
SETTINGS / DISPLAYS or if you are using a SMART-BOX under
SETTING & DATAVIEW. How to access this menu is described
in the operating instructions supplied with your transmitter or
Smart-Box.
ALARM VOLT (receiver low voltage warning)
If the receiver voltage falls below the set value, a low-voltage
warning is generated by the transmitter's RF module in the form
of a "general alarm tone" (regular beeping at a rate of approx.
one beep per second) or the "receiver voltage" speech output
message.
(ALARM TEMP): Temperature warning
If the receiver temperature exceeds the set temperature, a warn-
ing is generated by the transmitter’s RF module in the form of a
"general alarm tone" (regular beeping at a rate of approx. one
beep per second) or the "receiver temperature" speech output
message.
Cycle time (PERIOD)
If your system is used exclusively with digital servos, you can set
a cycle time (frame rate) of 10 ms. If your system includes some
or uses exclusively analogue servos, you should always select
20 ms, as many analogue servos cannot process the higher
frame rate and may respond by "jittering" or "growling". Not
important for connected speed controllers.
(Sensor at CH9):Telemetry sensor
This socket allows you to use either for telemetry or for an extra
channel (9). (Attention! Both together is not possible!) Switching
is done in this menu item. If you select “Yes”, the socket is con-
nected to the connection of a sensor. If you select “No” a jack
is connected to the control channel 9.
Language
Here you can set the display language in the receiver menu.
Select: German, English, French, Italian, Spanish.
RECEIVER 1.0 >
>ALARM VOLT: 3,8V
ALARM TEMP: 70° C
>CYCLE: 20ms
Sensor at CH9: No
LANGUAGE: English
Setting necessary when servos
are installed for additional
functions
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-10C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-10C in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info