782355
6
Zoom out
Zoom in
Previous page
1/14
Next page
Graule Maschinenbau GmbH ,
Robert-Bosch-Str. 7, D-73431 Aalen
Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de
8.2 Electric mains supply
Connect to an electric network according to the voltage and frequency given in the
nameplate!
Radial Arm Saw type ZS 135 and ZS 170 respectively, with a rotary current motor,
are delivered with some 2mt cable. The connection to a network may only
take place through a plug-in appliance type CEE-16A. All supply cords must be protected
by fuse with 16A.
When viewing the saw blade from the side, the sense of rotation must be clockwise. If the
sense of rotation is wrong you have to change two of the three electrical wires.
The electrical connection may only be made by an electrical specialist according to VDE
(German electrical engineer association).
Motor make FLENDER-HIMMEL:
5 wires connecting cables:
black-black-brown = L1 - L2 - L3 (current-carrying). These must be connected to R-S-T;
blue = NEUTRAL
yellow/green = EARTH
If the neutral conductor is disconnected, the green switch button does not hold
automatically.
A wrong connection causes the motor to overheat and possibly to burn out.
Motors are equipped with an electro-mechanical brake. A wrong connection causes the
destruction of the rectifier. The brake does not release anylonger and the motor overheats
when running.
8.3 Electrical switch with overload protection
The ON-OFF switch of the machine is mounted on the motor.
Green push-button: motor ON - red push-button: motor OFF
If the motor is overloaded or in case of power failure the machine switches off
automatically. Only after the motor has cooled off or after the power has come back the
machine may be switched on again.
8.4 Pneumatic connection
If the machine is equipped with a pneumatic material tension or a pneumatic saw blade spray
appliance, it must be connected through an attendance unit to an air network with a
compression of at least 6 bar. The tension pressure can then be adjusted through the
attendance unit.
8.5 Shavings exhaustion
The machine must be connected to an exhauster by means of the rear exhaustion connection
piece.
When cutting aluminium profiles, a shavings collecting bag out of cloth may also be
installed.
8.6 Installation of the roller conveyor (option)
A 60 x 40 x 3 x 440 mm joint pipe is packed together with the roller conveyor. This joint
pipe can be used for both left and right side installation of the roller conveyor on the
machine.
By using both short hexagon socket screws, secure the joint pipe to the casting platform
below the wood supporting table. The roller conveyor will then be secured with the first
transverse bar to the joint pipe, using two hexagon socket screws. The enclosed support foot
must be laterally secured to both longitudinal rails in the rear one-third. After adjusting both
elevation and alignment of the roller conveyor, screws must be tightened again.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graule ZS 135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graule ZS 135 in the language / languages: English as an attachment in your email.

The manual is 0.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info