782355
4
Zoom out
Zoom in
Previous page
1/14
Next page
Graule Maschinenbau GmbH ,
Robert-Bosch-Str. 7, D-73431 Aalen
Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de
position, to prevent pulling forward unintentionally. The saw blade is then perfectly located
in the lower saw blade protecting hood.
The material wooden supporting table with the insert and the vertical back stop shoulder
must always be in good condition. Defective tables and stop shoulders must be replaced.
Return spring device, which withdraws the tool slide into its rear starting position after
a saw cut, must be immediately replaced in case of breakage. The saw must not be operated
when the return spring device is faulty.
The ball-type nipple guide must be cleaned at regular intervals, so that the guiding elements
may run smoothly and the tool slide may be pulled back indipendently into its rear starting
position through the return spring device.
Lower saw blade protecting hood must be correctly set, so that the saw blade is entirely
covered in its lower area. Switch off the machine (disconnect the mains plug!) to remove
residual material fragments which might be got stuck.
CAUTION: Do not operate the machine if parts are damaged! Faulty parts must be
immediately replaced and in the meantime the machine must be stopped!
5. Qualified application.
Circular cross-cut and mitre-box saws type ZS 135 or ZS 170 may only be used for professional
cutting into sections or mitre cutting of following materials: wood with a rectangular or
square cross section, strip cutted panel materials, like particle board, wood core plywood
and Mdf-boards which are made fit for the cutting range, plastic profiles (duroplastic and
thermoplastic) and, in connection with hydraulic feed brakes, hollow extruded aluminium
profiles up to a wall thickness of approx. 4 mm . Profiles must have a safe support. Profile
sections must be adapted to the machining range. The saw blade must match the material to
be cut.
A qualified application also requires that the saw blade has a negative effective cutting
angle.
Any other different application shall be regarded as unsuitable and the manufacturer assumes
no responsibility for resulting damages of any kind. The risk shall be taken by the user alone.
The use of HSS-(high-speed steel) saw blades and cutting-off wheels is not allowed.
The machine must be connected to a large exhaustion plant.
During operation the machine must have a safe location.
A qualified application also requires that the manufacturer meets all specified operation,
maintenance and repair conditions, as well the operation and safety regulations of the
working instructions.
6. Other risks
Owing to the purpose of application of the machine design, the following remaining risks
may arise, even after taking all necessary safety precautions and despite a qualified
application:
Touching the saw blade during the cutting operation.
Slinging away of small wood fragments.
Breaking and slinging out of saw blade parts.
Damage to hearing during a long operating time without ear protection.
Emission of harmful dusts during operation without an exhaustion plant.
Danger of injury through the saw blade tooth when replacing saw blades.
7. Safety notes
The machine may only be operated and attended by people who are familiar with it and well
informed about the dangers. Repairs may only be made by qualified staff.
The machine must be operated in line with all appropriate regulations for prevention of
accidents as well as with the generally accepted requirements about safety and industrial
medicine.
No warranty is given by the manufacturer for any damage resulting from unauthorized
changes on the machine.
Improper use of high-speed machines can be dangerous! Therefore:
Read the instructions for use carefully before operating the machine.
Never work without the protective equipment as specified for each operation and do not
change anything in the machine that could be detrimental to its safety.
Children and young people are not allowed to operate the machine, except for young
people under supervision of an expert for training purposes.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graule ZS 135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graule ZS 135 in the language / languages: English as an attachment in your email.

The manual is 0.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info