782355
5
Zoom out
Zoom in
Previous page
1/14
Next page
Graule Maschinenbau GmbH ,
Robert-Bosch-Str. 7, D-73431 Aalen
Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de
Never work without a safety appliance or with a faulty machine or tool.
Worn out material supporting tables must be immediately replaced.
Use only circular saw blades allowed for this type of machine.
The use of cutting-off wheels or circular saw blades out of high-speed steel (HSS) is not allowed.
Do not use saw blades being cracked or modified in the shape.
The machine must have a permanent and safe place and must stand horizontally.
During repairs and when working to eliminate troubles disconnect the mains plug and wait
until the saw blade stops. The same also applies when removing stuck splinters.
Damaged cables and plugs must be immediately replaced.
Always wear tight-fitting clothes. Take off any ring, bracelet, watch or chain when working.
Wear safety glasses when cutting, to protect against chips being thrown around.
Sound pressure at work place normally exceeds 85 dB (A).
Therefore, wear an ear protection when working.
Start working only when the saw blade has reached its maximum speed.
Do not machine any part being too small or too big for the capability of the machine.
The machining of round woods or parts with an inadequate work support is prohibited.
Work only with sharp tools.
Do not work in a damp or wet environment, or in the surrounding area of combustible liquids or gas.
Wood dust resulting from cutting the wood is harmful to the sight and sometimes to the
health. If you do not work outside or in well ventilated rooms, the machine must be
connected to a shavings exhaustor with at least a 20 m/s air speed. The same applies when
machining plastic profiles, owing to formation of harmful steams when cutting at high speeds.
Only an electrical specialist may work at the electrical parts of the machine.
A regular cleaning of the machine, especially of leaders and material supporting tables
represents a high safety factor. Before starting this operation disconnect the mains plug.
Standing behind the machine during cutting is prohibited.
8. Starting and using the machine
8.1 Delivery and installation
After delivery, you should examine the machine at once to exclude "transport damage".
Should transport damages occur, inform the carrier at once.
Mount the machine on a sufficiently big table or console. A suitable machine tool table is
available as an accessory.
Fastening is done through the three 9 mm diameter bore holes on the mounting plate.
Turn the 4 screw bolts M 8 down to the table plate and fasten them with the nuts.
If the material supporting table is dismounted, use the 6 flat head bolts to mount it.
Should the machine be equipped with a pneumatic material tension, a suitable valve should
possibly be secured to the table board too.
During transport the saw carriage is locked into place by means of a knurled screw located
at the guide carriage, on the right behind the motor. Loosen the knurled screw and unscrew
approx. 1cm.
If the machine is equipped with a hydraulic feed brake (accessories), this can be pushed
together during transport. In this case unscrew the locking screw which secures the brass
tube in its mounting and push back the brass tube with its mounting as far as the retaining
ring and then pinch it off again.
After releasing the locking device behind the operating handle, the saw unit cab be pulled
forward.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graule ZS 135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graule ZS 135 in the language / languages: English as an attachment in your email.

The manual is 0.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info