782355
8
Zoom out
Zoom in
Previous page
1/14
Next page
Graule Maschinenbau GmbH ,
Robert-Bosch-Str. 7, D-73431 Aalen
Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de
9. Working notes
Check the elevation adjustment and verify the clamping of the mitre adjustment.
When sawing, the material must be placed on the back stop shoulder and must be held there
with the left hand or else it must be cramped with the pneumatic material tension. The
residual length to hold on must be at least 250 mm. Also carefully control the cut direction!
The holding hand or the clamping cylinder must lie outside the cutting plane. With the right
forefinger release the locking device behind the pull handle and pull forward the saw slide
through the material with the arm stretched, but not too fast. The feed speed must fit the
material to be cut.
Never saw from the front to the back!
The cut parts should not be too short, otherwise there is a risk that they are caught and flung
back by the saw blade teeth. During cutting, standing behind the machine is prohibited!
When cutting open profiles the self-supporting web or leg must be placed to the back
towards the stop shoulder or must be placed down. If this is not possible, the profile must be
toughened with an addition. When cutting aluminium profiles the saw blade must always be
greased with a lubricating stick, if there is no saw blade spray appliance.
10. Maintenance
Round rods of the ball-type nipple slaving must be cleaned daily to remove all splinters.
We recommend to lightly grease the blank parts from time to time.
Saw blades for wood must be regularly deresinified. When using saw blades for aluminium,
remove any residual material from the tooth spaces.
11. Eliminating faults
When eliminating faults always disconnect the mains plug!
The rotary current motor becomes very hot:
The motor runs only at 2 phases. The brake does not release.
Rubbing noise when the saw blade comes to a stop:
A chipping has got stuck between the protective device at the top or at the bottom and the
saw blade.
The motor switches off when idle running:
Voltage loss. The motor does not start again automatically because of the undervoltage
protection. The motor must be switched on again after the voltage has recovered.
The motor switches off when overstressed:
The overstress protection switches off the motor. The motor was overstressed. Edgeless saw
blade: the feed motion is too big.
The motor may only be switched on again after cooling.
Burns at cut places on wood:
Unsuitable or blunt saw blade.
The saw blade seizes up tightly into the cut material:
Saw blade is blunt or feed motion too fast. Use a saw blade with a negative frame angle.
Give more choke to hydraulic feed brake.
12. Guarantee
We assume legal liability for material and manufacturing defects to the exclusion of
following wearing parts: return spring, electric switch inset, motor brake, V-belts, as well
as damages due to overload breakage.
13. Appendix
Spare parts list
Electric wiring diagram
Pneumatic diagram
Change belts
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graule ZS 135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graule ZS 135 in the language / languages: English as an attachment in your email.

The manual is 0.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info