590655

Gossen Metrawatt METRISO PRIME plus Manual

13
Zoom out
Zoom in
Previous page
1/68
Next page
GMC-I Messtechnik GmbH 13
2.2.4 Symbols in the User Interface with Feature B1/B2
High-voltage module ready to be switched
on
Life endangering high voltage of up to 5.35 kV
is present at the test probes of the high-
voltage module.
Test completed successfully,
residual voltage less than 25 V
Display of phase angle
The specified limit value I
MAX
has been exceeded.
Current limiting has switched the device to the
“standby” mode.
The last voltage value measured before interrupting current
was exceeded, as well as interrupting current limit value
I
MAX
are displayed
Excessive temperature inside the test instrument
(high-voltage test)
Allow the device to cool for approximately 10 minutes.
2.3 Special Safety Precautions and Instructions
for Feature B1/B2
Precautions for the prevention of unauthorized start-up:
•Key switch
Precautions for the prevention of inadvertent start-up:
• Multiple key operation:
Before test voltage can be applied to the test probes by acti-
vating the trigger at the high-voltage switching pistol, the
START key must be pressed at the primary device.
• Two-hand operation:
Each of the high-voltage pistols is equipped with a trigger.
Both triggers must be activated simultaneously in order to ex-
pose both test probes.
• High-voltage switching pistol (pistol with yellow marking) with
double safety feature:
If the trigger at the high-voltage switching pistol is pulled to the
first point of mechanical resistance, the test probe is exposed.
High-voltage is not applied to the test probe until the trigger is
pulled beyond this point, assuming the device is switched on.
General Safety Precautions
• Integrated signal lamps indicate the switching status of the test
instrument.
• Test probes are electrically isolated from the mains:
This prevents current from flowing from the high-voltage
switching pistol to earth.
• Current limiting in the event of arc-over:
If the current limit value entered as a device parameter is ex-
ceeded due to arc-over, switching to the “standby” mode
takes place automatically.
•When mains voltage is restored after a power failure, switching to
the “standby” mode takes place automatically.
or
or
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt METRISO PRIME plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt METRISO PRIME plus in the language / languages: English as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt METRISO PRIME plus

Gossen Metrawatt METRISO PRIME plus User Manual - German - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info