656026
8
Zoom out
Zoom in
Previous page
1/15
Next page
Wireless Flash Shooting: Optical Transmission
This product is compatible with Sony Wireless Lighting System
(WL). It can function as either an optical wireless master or
slave flash. As a master unit, it can control Sony camera
flashes e.g. HVL-F60M, HVL-F43M and HVL-F32M via wireless.
As a slave unit, it can be controlled by wireless signals of Sony
camera flashes e.g. HVL-F60M, HVL-F43M and HVL-F32M.
For the restrictions of Sony camera flash’s wireless protocol,
there are several points to be noticed:
- 39 - - 40 -
Maximum Stroboscopic Flashes:
Master unit only has TTL and OFF mode. And M flash mode can
only be set under the slave mode.
Optical wireless lighting system (WL) do not have Multi mode.
When setting the slave unit to M mode, please set the group of
the master unit to TTL mode.
1/4
1/8
1/16
1/32
1/64
1/128
1
7
14
30
60
90
90
2
6
14
30
60
90
90
3
5
12
30
60
90
90
4
4
10
20
50
80
90
5
4
8
20
50
80
90
6-7
3
6
20
40
70
90
8-9
3
5
10
30
60
80
10
2
4
8
20
50
70
2
4
8
16
30
40
Hz
60-100
20-50
2
4
8
12
20
40
Flash
output
Even with multiple slave units, the master unit can control
all of them via wireless.
In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
Indoors
Outdoors
15m(49.2ft)
10m(32.8ft)
80°
8m(26.2ft) 12m(39.4ft)
Slave Unit Setting
Master Unit Setting
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
The backlight turns green
2 now.
Note: In the master unit mode < CTRL+>, you should set
the camera to wireless lighting mode (WL) when attaching
the camera flash to the camera. If the camera are not set
to WL state, a note “SET YOUR CAMERA “will be
displayed on the camera flash. As for how to set camera to
wireless lighting mode (WL), please refer to the camera’s
manual.
Flash Mode
SLOW
REAR
WL
Wirel essWirel essWirel ess
Press < > button so that
1 < CTRL+> is displayed on
the LCD panel.
Press < > button so that
1
< > and < > are
displayed on the LCD panel.
The backlight turns orange
2 now.
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
Using a tripod and a remote control is recommended.
A flash output of 1/1 and 1/2 cannot be set for stroboscopic
flash.
Stroboscopic flash can be used with“buLb”.
If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
Slave/Master Unit’s Positioning and Operation Range
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox V860IIS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox V860IIS in the language / languages: English as an attachment in your email.

The manual is 9,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info