656026
9
Zoom out
Zoom in
Previous page
1/15
Next page
- 41 - - 42 -
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 3
1 < > and turn the Select
Dial to choose a channel ID
from 1 to 4.
Press the <SET> button to
2 confirm.
CH
Note: As optical lighting system (WL) is restrained to Sony’s
wireless protocol, there is no much room for TT685S to
improve its optical transmission mode. Therefore, radio
transmission (2.4G) is recommended for its easier operation,
creative lighting effects, stable signals, etc.
Wireless Flash Shooting: Radio (2.4G) Transmission
You can set up three slave groups for TTL autoflash shooting.
With TTL autoflash, you can easily create various lighting effects.
Any flash settings for the slave units on the master flash in TTL
mode will be automatically sent to the slave units. So the only
thing you need to do is to set the master unit for each slave group
without any operation for the slave units at all during the shooting.
This flash can work in TTL /M /Multi / OFF flash modes when set
as a master unit.
Master Unit Setting
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
Press < > button so that
1 < > is displayed on the
LCD panel. If < MULTI>
is displayed, it means Multi
mode is ON.
The backlight turns green
2 now.
Even with multiple slave units, the master unit can control
all of them via wireless.
In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
Press Function Button 4
1 < > to choose the
group from M/A/B/C. Then,
press Function Button 3
< MODE > so that the
master unit can work in OFF
/ TTL flash mode. Choose
one of them as the flash
mode of master unit..
Exit Optical Wireless Lighting Mode
2. Setting Master Unit's Flash Mode
Flash Mode
SLOW
REAR
WL
Fill-flashFill- flashFill-flash
Set the camera to NON
1 wireless lighting mode.
Press < > Wireless
2 Selection Button to switch to
other modes.
Gr
Slave Unit Setting
Press < > button so that
1
< > and < > are
displayed on the LCD panel.
The backlight turns orange
2 now.
Press Function Button 4
1 < > to choose the
group from M/A/B/C. Then,
press Function Button 3
<MODE> so that the master
unit can work in OFF/TTL/M
flash mode. Choose one of
them as the flash mode of
master unit.
2. Setting Master Unit’s Flash Mode
Gr
Press < > button to
2 switch to Multi mode.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 3
1 < > and turn the
Select Dial to choose a
channel ID from 1 to 32.
CH
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox V860IIS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox V860IIS in the language / languages: English as an attachment in your email.

The manual is 9,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info