656026
6
Zoom out
Zoom in
Previous page
1/15
Next page
在使用本产品之前:
请先仔细阅读本手册,以确保您能安全使用。请保存好本手册以备将
来查询参考。
Before using this product:
Please read this user manual carefully in order to ensure your safety
and the proper operation of this product. Keep for future reference.
705-V862S0-00
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423
邮箱/E-mail: godox@godox.com
http://www.godox.com
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
Made In China
INSTRUCTION MANUAL
中英文双语 / Chinese English Bilingual
For Sony
TTL
Pioneering Camera FlashTTL Li-ion
Always keep this product dry. Do not use in rain or in damp
conditions.
This product contains high-voltage electronic parts. Touching
the high-voltage circuit inside it may result in electric shock. Do
not disassemble. Should repairs become necessary, this
product must be sent to an authorized maintenance center.
Stop using this product if it breaks open due to extrusion, falling
or strong hit. Otherwise, electric shock may occur if you touch
the electronic parts inside it.
Do not fire the flash directly into the eyes (especially those of
babies) within short distances. Otherwise visual impairment
may occur. When taking pictures for babies, keep the flash unit
at least 1 meter (3.3 feet) away from them. Using bounce flash
to reduce light intensity is also recommended.
Do not use the flash unit in the presence of flammable gases,
chemicals and other similar materials. In certain circumstances,
these materials may be sensitive to the strong light emitting
from this flash unit and fire or electromagnetic interference may
result.
Do not leave or store the flash unit in places where the ambient
temperature reads over 50°C (e.g. in automobile). Otherwise
the electronic parts may be damaged.
Thank you for purchasing this product.
This V860IIS camera flash applies to Sony DSLR series cameras
and is compatible with TTL autoflash. With this TTL compatible
flash, your shooting will become simpler. You can easily achieve a
correct flash exposure even in complex light-changing environments.
This camera flash features:
GN60 (m ISO 100, @200mm). 22 steps from 1/1 to 1/128.
Pro 2000mAh Li-ion Battery—1.5s recycle—650 full power pops.
Fully support camera flash. Workable as Master or Sony TTL
Slave unit in a wireless flash group.
Use dot-matrix LCD panel to make clear and convenient
operations.
With built-in 2.4GHz wireless remote system to support
transmitting and receiving.
Provided multiple functions, include HSS (up to 1/8000s),
FEC, etc.
Use optional FT-16S to adjust flash parameters & trigger the flash.
Stable consistency and color temperature with good even lighting.
Support with firmware upgrade.
For Your Safety
Foreword
- 27 - - 28 -
Foreword
For Your Safety
Name of Parts
Body
Control Panel
LCD Panel
What's in the Box of V860IIS Kit?
What's in the Box of V860IIS (only flash unit)?
Separately Sold Accessories
Battery
Attaching to a Camera
Power Management
Flash Mode: TTL Autoflash
FEC (Flash Exposure Compensation)
High-Speed Sync
Second-Curtain Sync
M: Manual Flash
Multi: Stroboscopic Flash
Wireless Flash Shooting: Optical Transmission
Wireless Settings
Setting Master Unit’s Flash Mode
Setting the Communication Channel
Wireless Flash Shooting: Radio (2.4G) Transmission
Wireless Settings
Setting Master Unit’s Flash Mode
Setting the Communication Channel
TTL: Fully Automatic Wireless Flash Shooting
M: Wireless Flash Shooting with Manual Flash
Multi: Wireless Flash Shooting with Manual Flash
Other Applications
Wireless Control Function
Sync Triggering
Auto Focus Assist Beam
Bounce Flash
Creating a Catchlight
ZOOM: Setting the Flash Coverage and Using the Wide Panel
Low Battery Warning
C.Fn: Setting Custom Functions
Protection Function
Technical Data
Troubleshooting
Firmware Upgrade
Compatible Camera Models
Maintenance
Contents
27
28
31
34
35
35
36
37
38
39
41
46
49
50
51
52
53
53
53
Conventions used in this Manual
This manual is based on the assumption that both the camera and
camera flash’s power switches are powered on.
Reference page numbers are indicated by “p.**”.
The following alert symbols are used in this manual:
The Caution symbol gives supplemental information.
The Note symbol indicates a warning to prevent shooting
problem.
- 29 - - 30 -
Pioneering Li-ion Camera Flash
RST
SET
LCD Panel
- 31 - - 32 -
Name of Parts
20
21
22
14
19
17
18
15
23
16
(1) TTL Autoflash
Zoom : zoom display (Page 48)
: Automatic
: Manual(Page 37)
TTL : TTL autoflash
Focus length (Page )48
: High-speed sync
(Page 37)
: Flash exposure
compensation (Page 36)
Distance indicator
display
Flash exposure
compensation amount
(2)M Manual Flash
The display will only show the settings currently applied.
The functions displayed above function buttons 1 to 4, such
as and , change according to settings’ status.
When a button or dial is operated, the LCD panel
illuminated.
M : Manual flash
Manual flash output
(3)Multi Flash
Multi : Stroboscopic flash
Number of flashes
Flash frequency
SYNC
01. Catchlight Panel
02. Built-in Wide Panel
03. Flash Head
04. Optic Control Sensor
05. Focus Assist Beam
06. Sync Cord Jack
07. Wireless Control Port
08. Hotshoe
09. Dot-marix LCD Panel
10. Lock Ring
11. Battery Compartment
12. USB Port
13. Slave Flash Ready Indicator
Body
14. <MODE> Mode Selection
Button / Lock button
15. < >Wireless Selection
Button
16. Select Dial
17. <SET> Set Button
18. ON/OFF Power Switch
19. < > Test Button / Flash
Ready Indicator
20. Function Button 1
21. Function Button 2
22. Function Button 3
23. Function Button 4
Control Panel
06
12
07
08
10
11
05
13
04
03
02
01
09
- 33 - - 34 -
Flash mode
: Group flash (radio transmission)Gr
Channel
: Radio transmission
wireless shooting
: Optic transmission
wireless shooting
(4) Optical Transmission Shooting
Master Unit
Slave Unit
: Slave
: Slave icon
Firing group
FEC
Separately Sold Accessories
The product can be used in combination with the following accessories
sold separately, so as to achieve best photography effects:
X1T-S wireless flash trigger, FT-16S power & trigger control, Mini
softbox, White & Silver reflector, Honeycomb, Color gels, Snoot, etc.
Features
1. This flash unit uses Li-ion polymer battery which has long runtime.
The available charge-and-discharge times are 500.
2. It is reliably safe. The inner circuit is against overcharge,
overdischarge, overcurrent, and short circuit.
3. Take only 2.5 hours to fully charge the battery by using the
standard battery charger.
Cautions
1. Do not short circuit.
2. Do not expose to rain or immerse into water. This battery is not
water proof.
3. Keep out of reach of children.
4. No over 24 hours’ continuous charging.
5. Store in dry, cool, ventilated places.
6. Do not put aside or into fire.
7. Dead batteries should be disposed according to local regulations.
8. If the battery had ceased using for over 3 months, please make a
full recharge.
Loading and Unloading the Battery
Battery
To load the battery, push the
1 battery compartment cover
downward and open it.
According to the triangle sign
2 on the battery pack, insert it
into the compartment until a
white knob locks the battery
with a click sound.
What’s in the Box of V860IIS Kit?
1. Flash Unit 2. Li-ion Battery Pack 3. Battery Charger 
4. Battery Charger Cable 5. Mini Stand 
6. Protection Case 7. Instruction Manual
1
2
What’s in the Box of V860IIS (only flash unit)?
1. Flash Unit 5. Mini Stand 6. Protection Case 7. Instruction Manual
5
6
3
4
Flash Mode: TTL Autoflash
This flash has three flash modes: TTL, Manual (M), and Multi
(Stroboscopic). In TTL mode, the camera and the flash will work
together to calculate the correct exposure for the subject and the
background. In this mode, multiple TTL functions are available:
FEC, HSS, second curtain sync, modeling flash, etc.
* Press <MODE> Mode Selection Button and three flash modes will
display on the LCD panel one by one with each pressing.
TTL Mode
Press <MODE> Mode Selection Button to enter TTL mode. The
LCD panel will display <TTL>.
Press the camera release button halfway to focus. The aperture
and effective flash range will be displayed in the viewfinder.
When the shutter button is fully pressed, the flash will fire a pre-
flash that the camera will use to calculate exposure and flash
output the instant before the photo is taken.
   FEC: Flash Exposure Compensation
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.
It is useful in situations where minor adjusting of the TTL system is
needed based on the environment.
Setting FEC:
Set the flash exposure
2 compensation amount.
Turn the Select Dial to set
the amount.
“0.3”means 1/3 step,
“0.7”means 2/3 step.
To cancel the flash
exposure compensation,
set the amount to “+0”.
Press < SET > button again
3 to confirm the setting.
Press Function Button 2
1 < >. The icon < >
and flash exposure
compensation amount will be
highlighted on the LCD
panel.
- 35 - - 36 -
Battery Level Indication
Make sure the battery pack is securely loaded in the flash. Check
the battery level indication on the LCD panel to see the remaining
battery level.
Battery Level Indication
3 grids
2 grids
1 grid
Blank grid
Blinking
To unload the battery, tap the
3 white knob and the battery
pack will pop out. Then close
the compartment.
Attaching to a Camera
Attach the Camera Flash.
1
Slip the camera flash’s
mounting foot into the
camera’s hotshoe all the
way.
Secure the Camera Flash.
2
Rotate the lock ring on the
mounting foot until it locks
up.
Detach the Camera Flash.
3
Rotate the lock ring on the
mounting foot until it is
loosened.
The battery level is going to be used out
immediately. And the flash will auto power off
in 1 minute.
Note: Please recharge the battery as soon as
possible (within 10 days). Then, the battery can be
used or be placed for long period.
Meaning
Full
Middle
Low
Lower battery, please recharge it.
Power Management
Use ON/OFF Power Switch to power the flash unit on or off. Turn off
if it will not be used for an extended period of time. Setting as a
master flash, it will turn the power off automatically after a certain
period (approx. 90 seconds) of idle use. Pressing the camera
shutter halfway or pressing any flash button will wake up the flash
unit. Setting as a slave flash, it will enter sleep mode after a certain
period (adjustable, 60 minutes by default) of idle use. Pressing any
flash button will wake it up.
C.Fn
C.Fn
Disabling Auto Power Off function is recommended
when the flash is used off camera. (C.Fn-APO, Page 49)
Slave Auto Power Off Timer is set to 60 minutes by
default. Another option “30 minutes” is available. (C.Fn-
Sv APOT, Page 49)
The flash output is adjustable from 1/1 full power to 1/128th power
in 1/3rd stop increments. To obtain a correct flash exposure, use a
hand-held flash meter to determine the required flash output.
M: Manual Flash
- 37 - - 38 -
Press < MODE > button so
1 that < M > is displayed.
Turn the Select Dial to choose
2 a desired flash output amount.
Press < SET > button again to
3 confirm the setting.
Figures displayed when reducing flash output level
Figures displayed when increasing flash output level
1/41/21/1
1/1-0.3
1/2+0.7
1/1-0.7
1/2+0.3
1/2-0.3
1/4+0.7
1/2-0.7
1/4+0.3
······
······
Flash Output Range
The following table makes it easier to see how the stop changes in
terms of f/stop when you increase or decrease the flash output. For
example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-
0.7, and then increase the flash output to more than 1/2, 1/2+0.3,
1/2+0.7, and 1/1 will be displayed.
Optical S1 Secondary Unit Setting
In M manual flash mode, press <S1/S2> button so that this flash can
function as an optic S1 secondary flash with optic sensor. With this
function, the flash will fire synchronously when the main flash fires,
the same effect as that by the use of radio triggers. This helps create
multiple lighting effects.
Optical S2 Secondary Unit Setting
Press <S1/S2> button so that this flash can also function as an optic
S2 secondary flash with optic sensor in M manual flash mode. This
is useful when cameras have pre-flash function. With this function,
the flash will ignore a single “preflash” from the main flash and will
only fire in response to the second, actual flash from the main unit.
S1 and S2 optical triggering is only available in M manual
flash mode.
Manual Off Camera High-speed Setting
In M manual flash mode, press < > button to select high-speed
mode and is displayed.
Set the flash frequency and
3 flash times.
Press Function Button 3
< > to select the flash
times. Turn the Select Dial to
set the number.
● Press Function Button 4
< > to select the flash
frequency. Turn the Select
Dial to set the number.
After you finish the setting,
press <SET> button and all
the settings will be displayed.
Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press <MODE> button so
1 that < > is displayed.
Turn the Select Dial to choose
2 a desired flash output.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
Number of Flashes / Flash Frequency = Shutter Speed
MULTI
SYNC
Hz
MULTI
With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
Multi flash mode cannot be set in high-speed sync mode.
Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
High-Speed Sync
High Speed Sync (FP flash) enables the flash to synchronize with all
camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
As high-speed sync setting is determined by Sony camera’s shutter,
please refer to your camera’s manual.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
Set Sony camera to Rear mode.
Wireless Flash Shooting: Optical Transmission
This product is compatible with Sony Wireless Lighting System
(WL). It can function as either an optical wireless master or
slave flash. As a master unit, it can control Sony camera
flashes e.g. HVL-F60M, HVL-F43M and HVL-F32M via wireless.
As a slave unit, it can be controlled by wireless signals of Sony
camera flashes e.g. HVL-F60M, HVL-F43M and HVL-F32M.
For the restrictions of Sony camera flash’s wireless protocol,
there are several points to be noticed:
- 39 - - 40 -
Maximum Stroboscopic Flashes:
Master unit only has TTL and OFF mode. And M flash mode can
only be set under the slave mode.
Optical wireless lighting system (WL) do not have Multi mode.
When setting the slave unit to M mode, please set the group of
the master unit to TTL mode.
1/4
1/8
1/16
1/32
1/64
1/128
1
7
14
30
60
90
90
2
6
14
30
60
90
90
3
5
12
30
60
90
90
4
4
10
20
50
80
90
5
4
8
20
50
80
90
6-7
3
6
20
40
70
90
8-9
3
5
10
30
60
80
10
2
4
8
20
50
70
2
4
8
16
30
40
Hz
60-100
20-50
2
4
8
12
20
40
Flash
output
Even with multiple slave units, the master unit can control
all of them via wireless.
In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
Indoors
Outdoors
15m(49.2ft)
10m(32.8ft)
80°
8m(26.2ft) 12m(39.4ft)
Slave Unit Setting
Master Unit Setting
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
The backlight turns green
2 now.
Note: In the master unit mode < CTRL+>, you should set
the camera to wireless lighting mode (WL) when attaching
the camera flash to the camera. If the camera are not set
to WL state, a note “SET YOUR CAMERA “will be
displayed on the camera flash. As for how to set camera to
wireless lighting mode (WL), please refer to the camera’s
manual.
Flash Mode
SLOW
REAR
WL
Wirel essWirel essWirel ess
Press < > button so that
1 < CTRL+> is displayed on
the LCD panel.
Press < > button so that
1
< > and < > are
displayed on the LCD panel.
The backlight turns orange
2 now.
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
Using a tripod and a remote control is recommended.
A flash output of 1/1 and 1/2 cannot be set for stroboscopic
flash.
Stroboscopic flash can be used with“buLb”.
If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
Slave/Master Unit’s Positioning and Operation Range
- 41 - - 42 -
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 3
1 < > and turn the Select
Dial to choose a channel ID
from 1 to 4.
Press the <SET> button to
2 confirm.
CH
Note: As optical lighting system (WL) is restrained to Sony’s
wireless protocol, there is no much room for TT685S to
improve its optical transmission mode. Therefore, radio
transmission (2.4G) is recommended for its easier operation,
creative lighting effects, stable signals, etc.
Wireless Flash Shooting: Radio (2.4G) Transmission
You can set up three slave groups for TTL autoflash shooting.
With TTL autoflash, you can easily create various lighting effects.
Any flash settings for the slave units on the master flash in TTL
mode will be automatically sent to the slave units. So the only
thing you need to do is to set the master unit for each slave group
without any operation for the slave units at all during the shooting.
This flash can work in TTL /M /Multi / OFF flash modes when set
as a master unit.
Master Unit Setting
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
Press < > button so that
1 < > is displayed on the
LCD panel. If < MULTI>
is displayed, it means Multi
mode is ON.
The backlight turns green
2 now.
Even with multiple slave units, the master unit can control
all of them via wireless.
In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
Press Function Button 4
1 < > to choose the
group from M/A/B/C. Then,
press Function Button 3
< MODE > so that the
master unit can work in OFF
/ TTL flash mode. Choose
one of them as the flash
mode of master unit..
Exit Optical Wireless Lighting Mode
2. Setting Master Unit's Flash Mode
Flash Mode
SLOW
REAR
WL
Fill-flashFill- flashFill-flash
Set the camera to NON
1 wireless lighting mode.
Press < > Wireless
2 Selection Button to switch to
other modes.
Gr
Slave Unit Setting
Press < > button so that
1
< > and < > are
displayed on the LCD panel.
The backlight turns orange
2 now.
Press Function Button 4
1 < > to choose the
group from M/A/B/C. Then,
press Function Button 3
<MODE> so that the master
unit can work in OFF/TTL/M
flash mode. Choose one of
them as the flash mode of
master unit.
2. Setting Master Unit’s Flash Mode
Gr
Press < > button to
2 switch to Multi mode.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 3
1 < > and turn the
Select Dial to choose a
channel ID from 1 to 32.
CH
Setting <Multi>
1 stroboscopic flash.
Press <MODE> button so
that < MULTI> is
displayed.
● Setting the stroboscopic
flash. (Page 38)
- 43 - - 44 -
Slave Unit Setting
2
Set the V860IIS that to be
controlled as the wireless
slave unit. (Page 42)
● The slave unit can be set
as A/B/C.
Check the communication
3 channel
If the master unit and
slave unit(s) are set to a
different channel, set them
to the same channel.
(Page 42)
Position the camera and
4 flashes
Position the camera and
flashes as the picture
shows. (Page 40)
Check that the flash is
5 ready
Check that the master
flash ready indicator is
lightened.
● When the slave flash
ready indicator is ready,
the AF-assist beam
lighting area will blinks at
1 second intervals.
Check the flash operation
6
Press the master unit’s
Test Button< >.
Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
The slave unit might be out of order or fire an unwanted flash
due to the nearby fluorescent lamp or computer screen.
If the slave unit’s auto power off function is workable, press
the master unit’s test button to power it on. Please note that
test firing is unavailable during the camera’s regular
metering time.
The effective time of slave auto power off is changeable.
(C.Fn-Sv APOT/ Page 49)
By making some settings, the auto AF-assist transmitter will
not blink after the slave unit’s flash ready indicator is
lightened. (C.Fn-AF/ Page 49)
Using Fully Automatic Wireless Flash
The FEC and other settings that set on the master unit will also be
appeared on the slave unit automatically. The slave unit does not
need any operation. Use the following settings to make wireless
flashes according to the same methods with normal flash shooting.
Flash Exposure Compensation ( / Page 36
About Master Unit
Use two or more master units. By preparing several cameras that
with master units flash attached, cameras can be changed in
shooting while keeping the same lighting source (slave unit).
5. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Gr
Setting the flash mode to
1 <M>
Press Function Button 4
< > to choose groups.
Then, press Function
Button 3 < MODE > to set
the flash to M mode.
Setting flash output
2
When choosing the group,
press Function Button 2
< > to select the
power output. Turn the
Select Dial to set the flash
output of the groups.
Press the <SET> button
to confirm.
Taking the picture
3
Each group fires at the set
flash ratio.
6. Multi: Wireless Flash Shooting with Manual Flash
Press the <SET> button to
2 confirm.
Autoflash Shooting with One Slave Unit
4. TTL: Fully Automatic Wireless Flash Shooting
Master Unit Setting
1
Attach a V860IIS camera
flash on the camera and
set it as the master unit.
(Page 42)
M/A/B/C can be set as
TTL mode independently.
- 45 - - 46 -
Transmission distance is about 100m.
● Use the supplied mini stand to position the slave unit.
● Before shooting, perform a test flash and test shooting.
● The transmission distance might be shorter depending on
the conditions such as positioning of slave units, the
surrounding environment and whether conditions.
You can divide the slave units into two or three groups and perform
TTL autoflash while changing the flash ratio (factor). In addition, you
can set and shoot with a different flash mode for each firing group,
for up to 3 groups.
Wireless Multiple Flash Shooting
A
B
Function
Distance
Channel
To be Disturbed
Radio Transmission
100m
1~32
Hard
Optical Transmission
15m
1~4
Easy
A
B
C
Auto Shooting with
Two Slave Groups
Auto Shooting with
Three Slave Groups
Slave/Master Unit's Positioning and Operation Range
Autoflash Shooting with One Slave Unit
Other Applications
Wireless Control Function
The flash unit is built in with a Wireless Control Port so that you can
wirelessly adjust the power level of the flash and the flash triggering.
To control the flash wirelessly, you need a FT-16S
remote control set (on-camera and on-flash).
Insert its receive end into the Wireless Control
Port on the flash and insert the transmit end into
the camera hot shoe. Settings made on the
hotshoe-mounted transmit and receive ends
will be wirelessly communicated
to the flash. Then you can
press the camera shutter
release button to trigger
the flash. You can also hold
the transmit end at hand to
control your off-camera flash.
For full instructions on the use of FT series remote control, see its user
manual.
Sync Triggering
The Sync Cord Jack is a Φ2.5mm plug. Insert a trigger plug here
and the flash will be fired synchronously with the camera shutter.
Auto Focus Assist Beam
In poorly-lit or low-contrast shooting environments, the built-in auto
focus assist beam will automatically light on to make it easier for
autofocus. The beam will light up only when autofocus is difficult
and get out as soon as the autofocus becomes correct.
If you want to turn off the auto focus assist beam, set the “AF” to
“OFF” on the C.Fn settings.
If you find the auto focus assist beam does not light up, this
is because the camera has got a correct autofocus.
Position
Center
Periphery
Effective Range
0.6~10m / 2.0~32.8 feet
0.6~5m / 2.0~16.4 feet
Wireless shooting using radio transmission has advantages over
wireless shooting using optical transmission, such as being less
affected by obstacles, and not having to point the slave unit’s
wireless sensor toward the master unit. The main functional
differences are as follows:
Using a flash (master/slave) with a radio transmission wireless
shooting function make it easy to shoot with advanced wireless
multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in the
picture. You can then perform wireless TTL autoflash shooting just
by setting the master unit to <TTL>.
Bounce Flash
By pointing the flash head toward a wall or ceiling, the flash will
bounce off the surface before illuminating the subject. This can
soften shadows behind the subject for a more natural-looking shot.
This is called bounce flash.
To set the bounce direction, hold the flash head and turn it to a
satisfying angle.
360
-7-90
If the wall or ceiling is too far away, the bounced flash might
be too weak and result in underexposure.
The wall or ceiling should be a plain, white color for high
reflectance. If the bounce surface is not white, a color cast
may appear in the picture.
Creating a Catchlight
With the catchlight panel, you can create a catchlight in the subject’s
eyes to add life to the facial expression.
Point the flash head upward
1 by 90°.
Pull out the wide panel. The
2 catchlight panel will come out
at the same time.
Push the wide panel back in.
3
Push in only the wide panel.
Follow the same procedures
as for bounce flash.
Point the flash head straight ahead and then upward by
90°. The catchlight will not appear if you swing the flash
head left or right.
For best catchlight effect, stay 1.5m/4.9ft away from the
subject.
- 47 - - 48 -
ZOOM: Setting the Flash Coverage and Using
the Wide Panel
The flash coverage can be set automatically or manually. It can be
set to match the lens focal length from 20 mm to 200mm. Also, with
the built-in wide panel, the flash coverage can be expanded for
14mm wide-angle lenses.
In Manual Zoom mode, press the
<ZOOM/C.FN> button.
Turn the Select Dial to change
the flash coverage.
If < > is displayed, the flash
coverage will be set
automatically.
If you set the flash coverage manually, make sure it covers
the lens focal length so that the picture will not have a dark
periphery.
Using the Wide Panel
Pull out the wide panel and place it
over the flash head as shown. The
flash coverage will then be extended
to 14 mm.
The catchlight panel will come out
at the same time. Push the
catchlight panel back in.
The <ZOOM/C.FN> button will not
work.
Low Battery Warning
If the battery power is low, < >
will appear and blink on the LCD
panel. Please replace the battery
immediately.
C.Fn: Setting Custom Functions
The following table lists the available and unavailable custom
functions of this flash.
m/ft
APO
AF
Sv APOT
BEEP
LIGHT
LCD
m
ft
ON
OFF
ON
OFF
60min
30min
ON
OFF
12sec
OFF
ON
0~9
Distance indicator
Auto power off
AF-assist beam
Slave auto power
off timer
Beeper
Backlighting time
LCD contrast ratio
- 49 - - 50 -
C.Fn Custom Functions
Custom Function
Signs
Function
Setting No. Settings & Description
m
feet
ON
OFF
ON
OFF
60min
30min
ON
OFF
Off in 12 sec.
Always off
Always lighting
10 levels
1. Press <Zm/C.Fn> Backlight/Custom Setting Button for 2 seconds
or longer until C.Fn menu is displayed. TheVer x.x” in the top-
right corner refers to the software version.
2. Select the Custom Function No.
Turn the Select Dial to select the Custom Function No.
3. Change the Setting.
Press<SET> button and the Setting No. blinks.
Turn the Select Dial to set the desired number. Pressing <SET>
button will confirm the settings.
After you set the Custom Function and press Function Button 4
< > to exit, then the camera will be ready to shoot.
4. In the C.Fn states, long press the “Clear” button for 2 seconds
until “OK”is displayed on the panel, which means the values in
C.Fn can be reset.
Protection Function
1. Over-Temperature Protection
To avoid overheating and deteriorating the flash head, do not fire
more than 30 continuous flashes in fast succession at 1/1 full
power. After 30 continuous flashes, allow a rest time of at least 10
minutes.
If you fire more than 30 continuous flashes and then fire more
flashes in short intervals, the inner over-temperature protection
function may be activated and make the recycling time over 10
seconds. If this occurs, allow a rest time of about 10 minutes, and
the flash unit will then return to normal.
When the over-temperature protection is started, is shown on
the LCD display.
Number of flashes that will activate over-temperature protection:
Meaning
A failure occurs on the recycling system so that the
flash cannot fire.
Please restart the flash unit. If the problem still exists,
please send this product to a maintenance center.
The system gets excessive heat. Please allow a rest
time of 10 minutes.
The voltage on two outlets of the flash tube is too high.
Please send this product to a maintenance center.
There are some errors occurred during the upgrading
process. Please using the correct firmware upgrade
method.
Prompts on LCD Panel
E1
E2
E3
E9
2. Other Protections
The system provides real-time protection to secure the device and
your safety. The following lists prompts for your reference:
Number of flashes that will activate over-temperature protection in
high-speed sync triggering mode:
Power Output Level
1/1
1/2 +0.7
1/2 +0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
Number of Flashes
30
40
50
60
100
200
300
500
1000
Power Output
1/1
1/2(+0.3,+0.7);
1/4(+0.3,+0.7)
1/8(+0.3,+0.7);
1/16(+0.3,+0.7)
1/32(+0.3,+0.7);
1/64(+0.3,+0.7);
1/128(+0.3,+0.7);
Times
15
20
30
40
50
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox V860IIS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox V860IIS in the language / languages: English as an attachment in your email.

The manual is 9,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info