725140

Gloria Multibrush SpeedControl Manual

26
Zoom out
Zoom in
Previous page
1/56
Next page
26
GB
! Do not start or operate device if
bystanders are in the danger zone.
! Never put your hands or feet near to
the rotating brushing equipment!
! Never clean if others, in particular
children or animals, are in the area!
! Never use the device in the rain.
You can regulate the speed of the
brush by pressing the speed control
on the adjustment wheel (R).
Hold the device securely by the
handle (A) and additional handle (E)
and switch on the device by pressing
and holding the ON/OFF safety
switch (D) in handle (A).
! In case of work interruptions or
danger, release the ON/OFF safety
switch (D) immediately.
6.1.2 Assembly of the brushing
tools
Figures 12 - 20
CAUTION! RISK OF BURNS
CAUSED BY HOT PARTS!
During assembly or conversion work
the drive parts of the device or
components can still be very hot
and may cause burns.
It is therefore important to observe
the following safety instructions:
! Wear protective gloves during
assembly!
Disassembly of surface brush followed by
assembly of the joint brush
! Switch off the device and disconnect
the power cord (C) from the power
supply.
Open the locking device (K) of
the guide arm (M), as shown in the
illustration.
With the lock applied (K) remove the
guide arm (M) and then the surface
brush (N).
Now open the locking device (K)
of the drive arm (P), as shown in the
illustration and remove, with the lock
applied, (K) the drive arm (P) with
safety guard (O).
! The surface brush is now successfully
dismantled.
Put the guiding wheel (I), as shown in
the illustration, on the steering side of
the motor/gear unit (L). Now slide the
lock (K) into open position , hold
this and press the guiding wheel (I)
further onto the coupling shaft up to
the stop.
Release the spring-loaded locking
device (K). The guiding wheel (I) is
locked when the locking device
independently returns to its original
position .
Put the pre-assembled joint brush
unit, as illustrated, on the drive side of
the motor/gear unit (L). Slide the lock
(K) into open position , hold this
and press the joint brush unit further
into the drive shaft up to the stop.
Release the spring-loaded locking
device (K), the joint brush unit is
10
11
12
13
14
15
16
Speed recommendations for
GLORIA brushes
Position 1-2 soft brushes (wood brush)
Position 3-4 harder brushes (stone brush)
Position 5-6 joint brush (wire brush)
RZ_MULTIBRUSH_DE_GB_FR_NL_978410-1_Text_GB 10.11.16 15:55 Seite 26
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gloria Multibrush SpeedControl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gloria Multibrush SpeedControl in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info