Manual Gloria Multibrush SpeedControl (page 25 of 56) (English, German, Dutch, French)

725140

Zoom out

Zoom in

1/56

5 Assembly

Figures 1 - 6

NOTE!

Your device is supplied with the

surface brush pre-assembled.

Loose parts supplied must be

as sembled accordingly when

working with the joint brush.

! After removing from the packaging,

loosen screw connection (G) .

Next, turn handle (A) 45° as shown in

fig ure and adjust the length of

the telescopic tube (F) according to

your body height, as illustrated.

5 locking positions are available.

In the selected position, turn handle

(A) a further 45° and tighten the

height of the telescopic tube (F) with

the screw connection (G) by hand.

! As the device should always be

guided and operated with two

hands, fit the additional handle (E) as

shown in the figure , adjust the

height and screw the additional

handle (E) tightly into place .

6 Commissioning

WARNING! BEFORE USE OBSERVE

CHAPTER 2 “FOR YOUR SAFETY”.

ATTENTION! Improper use of the

device poses a risk of damage to

property!

You should therefore observe the

following safety instructions:

! Clean the roller/joint brush (N/J)

before each cleaning operation.

! The air inlet openings on the

motor/gear unit (L) must not be

blocked or covered.

! Check on a small, if possible hidden

area, that the ground to be cleaned

will not be damaged by the brush-

ing action.

! Never use the device too long on

one spot, always guide at walking

pace.

6.1 Operation

Figures 7 - 11

Slide the loop of the extension cable

into the designated cable strain relief

(B) in the handle (A) and fix it in the

designated clip.

NOTE!

! The performance of the equipment

may decrease if unnecessarily long

extension cables (>25 m) are used.

! If cable reels are used, unroll the

en tire cable.

! The cross-section of the cable used

must be 1.5 mm2.

Always place the device parallel on

the ground which is to be cleaned.

Identify the most comfortable but also

most effective working angle for your-

self and then adjust the 5 click-stop

safety guard (O) so that the rubber lip

is just above the ground.

! Make sure that the surface to be

cleaned is free from debris e.g. stones,

screws etc., which could be flung up.

Use an extension cable to connect the

device to a power outlet (230 V AC).

CAUTION! RISK OF INJURY FROM

ROTATING BRUSHING TOOL!

! Never start the device in a tilted

position!

RZ_MULTIBRUSH_DE_GB_FR_NL_978410-1_Text_GB 10.11.16 15:55 Seite 25

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gloria Multibrush SpeedControl in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gloria Multibrush SpeedControl Manual

Product: