479876
6
Zoom out
Zoom in
Previous page
1/7
Next page
11.0 - VEHICLE CODE PROGRAMMING
In presence of a CAN-BUS line, the alarm needs a configuration depending on the vehicles model and
make.
The alarm is supplied without any programming, since Gemini does not know the vehicle on which the
module will be installed.
For this reason, programming has to be carried out during installation.
Indeed, even in the same vehicle's brand, operating differences are possible, according to the model
(es. Coupè o station wagon).
The vehicle's codes are given in the supplementary leaflet included in the alarm
packaging (the codes are updated at the packaging time).
Please refer to our web site “www.gemini-alarm.com” for updating information
(private area).
To program the vehicle code, proceed as follows.
When installation is complete, connect the 20-way wiring harness connector to the 20-way
system connector.
Push and hold the button located on the front of the alarm control unit until the LED is switches on.
Release the button the LED will switch off.
After a short pause, the LED will start flashing.
Count the number of LED flashes until it correspondes to the first number of the code, then press
the button on the front of the control unit.
After a short pause, the led will start flashing again.
Count the number of LED flashes until it correspondes to the second number of the code, then
press the button on the front of the control unit.
After a short pause, the led will start flashing again.
Count the number of LED flashes until it correspondes to the third number of the code, then press
the button on the front of the control unit.
At the end of programming procedure, the alarm will «repeat» the entered code, by flashing the
LED.
Verify the alarm system operation using the original radio control lock button of the vehicle.
If the entered code is correct and correspondes to the vehicle, the alarm will operate correctly.
If the code has been entered incorrectly repeat the procedure.
The table below refers the values corresponding to the LED flashes that have been entered in the
alarm.
!
!
!
!
!
!
!
!
!
!
!
!
!
.
FLASHFLASH
Sixth flash
Seventh flash
Eighth flash
Ninth flash
Tenth flash
First flash
Second flash
Third flash
Fourth flash
Fifth flash
VALUEVALUE
Number value-6-
Number value-7-
Number value-8-
Number value-9-
Number value-0-
Number value-1-
Number value-2-
Number value-3-
Number value-4-
Number value-5-
12.0 - E
“FIAT XXXXX”.
XAMPLE OF ALARM MODULE CODE PROGRAMMING
For better understanding of coding,described below the procedure for entering the vehicle code.
In the given example, the code 1-0-3 corresponds hypothetically to the car
Connect the 20-way wiring harness connector to the 20-way system connector.
.Push and hold the button shown in figure, until the LED is switches on
Release the button the LED switches off.
After 3/4 second pause the LED will start with the first sequence of flashes.
Push the button at firts LED flashing, corresponding to value “1”.
Push
Push
Push
FIRST FLASH
3/4 seconds
After 3/4 second pause the LED will start with the second sequence of flashes.
Push the button at tenth LED flashing, corresponding to value “0”.
After 3/4 second pause the LED will start with the third sequence of flashes.
Push the button at third LED flashing, corresponding to value “3”.
When the last digit has been entered, the alarm will “repeat” the entered code.
Press the vehicle radio control lock/unlock buttons to verify the alarm operation.
Eventually disconnect the 20-ways connector and reconnect it after few seconds.
TENTH FLASH
THIRD FLASH
ONE FLASH AND
SHORT PAUSE
TEN FLASHES AND
SHORT PAUSE
THREE FLASHES
AND SHORT PAUSE
!
PAGE 10 PAGE 11
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7833 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7833 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info