479876
2
Zoom out
Zoom in
Previous page
1/7
Next page
2.0 - GENERAL NOTE FOR INSTALLATION
Dear installer, this manual has been written based on a complete system, therefore some functions,
electrical connections and other can be present in one alarm version and not in another.
In order to avoid repetitions in the manual, before installing the alarm, verify its version and then
follow the suitable instructions.
Furthermore, in order to carry out correctly the various procedures required, please
Device power supply (positive and ground).
Positive under key (+15/54)
Bonnet switch (if not on CAN-BUS line).
CAN-BUS line.
same as 7833 without self-powered battery.
VERIFY VERY
CAREFULLY ALL THE ELECTRICAL CONNECTIONS, IN PARTICULAR THE CONNECTIONS
LISTED BELOW:
GEMINI 7832:
!
!
!
!
PAGE 02
3.0 - FUNCTIONS
!
!
!
!
!
!
!
!
!
!
System arming and disarming by the vehicle original remote.
Acoustic arming/disarming signaling (excludable by programming).
Optical signalling (programmabili per inserimento e disinserimento se non presenti sul veicolo).
Perimetric protection.
Volumetric protection (excludable by arming).
Electrical engine immobiliser.
Negative output for additional siren.
Comfort negative output (about 20 seconds) or satellite system control.
LED memory.
Multifunction electronic key (random rolling code, 4,2 milliard of different codes).
Furthermore, in order to indicate to the installer and to the user some particular functions or
connections, an icon symbology has been used, which is briefly described below:
4.0 - OPERATING DESCRIPTION
PAGE 03
4.1 - COMPLETE SYSTEM ARMING
Press the lock button on the original radio control of the vehicle or insert the electronic key into the
specific receptacle.
Arming will be indicated by two short acoustic signals and by a number of optical signals (default
vehicles manufacturer setting).
Indications useful for the installer.
This icon indicates to the installer a diversificated operating, according to the connection
and the programming of the system or it simply provides indications useful for the
installation.
In case the vehicle has not optical signals when is closed, it is possible to activate these
signals by programming.
In this case, when the system is armed, two optical signals will be emitted
Indications useful for the user.
The user with indications for a diversificated use of the system or it simply provides
indications useful for the use.
!
!
4.2 - SYSTEM ARMING WITH SENSOR EXCLUSION
This function allows the user to arm the system, with volumetric protection excluded.
To active this function, the system must be disarmed and the ignition switched in “OFF” position and
than proceed as follows:
Turn the vehicle ignition key in “ON” position and wait for one second the status LED switches off
(the drivers door can be open or close at this point).
Introduce the electronic key into the receptacle; t
.
Turn the vehicle ignition key in “OFF” position.
!
!
!
he status LED will flash for one second and two
short acoustic signals will indicate the exclusion of volumetric sensors
When an immediate re-arming of volumetric sensors is required, switch the vehicle
ignition key in “ON” and “OFF” position.
1.0 - CONTENTS
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
11.0
12.0
16.0
- CONTENTS..... .......................................................................................................
- GENERAL NOTE FOR INSTALLATION..................................................................
- FUNCTIONS...........................................................................................................
- OPERATING DESCRIPTION.................................................................................
4.1 - Complete system arming......................................................................................
4.2 - System arming with sensor exclusion...................................................................
4.3 - Passive arming.....................................................................................................
4.4 - Arming inhibit time.................................................................................................
4.5 - System armed.......................................................................................................
4.6 - Alarm, inhibit time and alarm cycles.....................................................................
4.7 - System disarming.................................................................................................
4.8 - Emergency disarming by electronic key...............................................................
4.9 - Alarm memory.......................................................................................................
- ELECTRICAL CONNECTIONS..............................................................................
- CONNECTOR TABLE............................................................................................
- .............................................
- COMPLETE ELECTRIC DIAGRAM........................................................................
- SYSTEM PROGRAMMING............... ..................................................
...............................................................................................
........................................................................................
....................................................................
.........................................................................................
.................................................................................................
....................................................................................
................................................................
-.
.....................................
..............................................................................
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEE) DIRECTIVE....
WARRANTY CONDITIONS...................................................................................
- TECHNICAL DATA...............................................................................................
CONNECTION FOR TURN SIGNALS ACTIVATION
...................
9.1 - Acoustic signalling
9.2 - Impulse optic signalling
9.3 - Optic signalling by arming/disarming
9.4 - System passive arming
9.5 - Negative comfort
9.6 - Satellite system activation
- SYSTEM PROGRAMMING EXAMPLE
VEHICLE CODE PROGRAMMING .....................................................................
- VEHICLE CODE PROGRAMMING EXAMPLE...............
- ADD NEW ELECTRONIC KEY
-
-
10.0
13.0
14.0
15.0
PAGE 02
PAGE 02
PAGE 03
PAGE 03
PAGE 03
PAGE 03
PAGE 04
PAGE 04
PAGE 04
PAGE 04
PAGE 04
PAGE 04
PAGE 05
PAGE 05
PAGE 06
PAGE 06
PAGE 07
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 08
PAGE 09
PAGE 10
PAGE 11
PAGE 12
PAGE 12
PAGE 13
PAGE 13
UK
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7833 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7833 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info