813466

Gazco Marlborough Electric ECO Manual

7
Zoom out
Zoom in
Previous page
1/52
Next page
7
When in Daily Timer Mode switching the appliance off with the remote
will stop the light output. The heat output will continue according to
the timer settings.
Adjusting the Set Temperature
Press the ‘+’ or ‘-’ button to increase or decrease the temperature on the
basis of COMF temperature.
COMF means the actual temperature is the same as setting.
ECO means the actual temperature is 2℃ lower than the setting
temperature.
ECO- means 4℃ lower.
COMF+ means 2℃ higher.
COMF++ means 4℃ higher.
Adaptive start control
According to room temperature and set-pointed temperature, the heater will
automatically determine the appropriate time to heat to ensure that it will
reach the set-pointed temperature in the set time (up to 45 minutes prior to
the set time).
Flame Colour Adjustment
Press button to enter the flame adjustment screen.
There are 3 flame colour options, indicated by the number.
There are 6 levels of brightness, including off. This is indicated by the bar,
with the blank bar indicating off.
Brightness Level
Colour
Option
Press the ‘’ or ‘’ button to cycle through the flame colour options.
Press the ‘+’ button to increase the flame brightness.
Press the ‘-’ button to decrease the flame brightness until off.
Fuel Bed Colour Adjustment
Press to enter the fuel bed light adjustment screen.
There are 14 fuel bed colour options, indicated by the number.
There are 6 levels of brightness, including off. This is indicated by the bar,
with the blank bar indicating off.
Brightness
Level
Colour
Option
Press the ‘’ or ‘’ button to cycle through the fuel bed colour options.
Press the ‘+’ button to increase the fuel bed brightness.
Press the ‘-’ button to decrease the fuel bed brightness until off.
Normal Control Mode
Normal Control Mode is the default setting.
Alternatively press button until the logo is shown at the upper right
corner of the screen.
Press the ‘+’ or ‘-’ button to adjust the setting temperature from 17 ℃ to
25℃.
Press button to turn the heat on/off, ON or OFF will show at
the lower right corner of the screen.
Note: It is normal for the fan heater to stop running for periods of time. This
happens if the room temperature is higher than the temperature set on the
control.
The heater indicator will be turned off after 10s if the flame is switched ON.
The heater indicator will stay ON if only the heating function is used.
When in Normal Control Mode switching the appliance off with the
remote will stop both the light and heat output.
Count Down Timer
This setting is only in normal heating control mode. It allows the appliance
to be returned to Standby after a set period of time. The heater must be
switched on to use this function.
Press to cycle through the setting from Off and 0.5 hours to 9 hours.
Timer logo and remaining time will show on the screen.
The heater of appliance can be automatically run by using daily timer and
weekly timer on the remote.
Battery
The battery power level is indicated at the top right of the remote control
screen.
Battery Full No action required
Battery Half Power Ensure new batteries are available.
Battery Empty Replace batteries immediately
Battery replacement is recommended after 1 year. The Remote requires two
1.5V alkaline AAA batteries.
Changing the batteries will not affect the Timer Mode settings,
however, the clock may need adjusting.
ENGLISH
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Marlborough Electric ECO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Marlborough Electric ECO in the language / languages: English, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 3.32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info